4. Is installing a garbage disposal worth the additional water expense? On average, a modern faucet runs 2.5 gallons of water per minute, or 900 gallons per year based upon the average annual household usage in the U.S. Depending on how often you use your disposerl, your home’s water usage, and water bill, will rise. This is one factor you’ll need to consider before deciding whether or not to buy a garbage disposal.

I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.


Garbage disposals with stainless steel grinding blades and turntables make easy work of leftover meatloaf and biscuits. These blades will stay strong and last for years. High-power grinding motors hit maximum speeds quickly. This means jams and clogs are less likely to happen. Make sure to keep the faucet running for about 60 seconds after you turn off the disposal. Doing this ensures that all of the food particles make it down the hose.
If your disposal grinds poorly, make sure that you are running enough water while operating the unit and that you are not grinding matter that you shouldn’t. If you can hear the garbage disposal running but it is not grinding, the blades may be broken. It’s usually easier and cheaper to just replace the entire unit. See How to Install a Garbage Disposal.

Hang the disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. The disposal will now hang by itself. Tighten the three mounting screws, ultimately tightening each screw a few turns at a time until the mounting assembly is evenly and tightly seated against the bottom of the sink.
Need Help?  Have a question or comment?1-888-827-4223Email UsGet Exclusive Offers & Expert TipsJOINTerms of UsePrivacy PolicyInterest Based AdsFor U.S. Residents Only © 2018 Ace Hardware. Ace Hardware and the Ace Hardware logo are registered trademarks of Ace Hardware Corporation. All rights reserved. For screen reader problems with this website, please call 1-888-827-4223 or email [email protected]
If there is nothing visible clogging your disposal unit, the flip switch on your garbage disposal unit may have turned the unit off. This little red switch is located underneath your unit and protects against overheating and arcing situations. You can try pushing the red switch to reset the garbage disposal unit. Test your unit by turning it on. If it still won't turn on or makes a humming noise, unplug the unit or turn it off at the breaker box, and move to step 4.
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
Our Minneapolis – St. Paul plumbers assist customers with garbage disposal installation by helping them choose between a continuous feed garbage disposal or a batch feed utility. Our plumbers will discuss the best options for your home and lifestyle. Some of the benefits of our garbage disposals include anti-jamming technology, plastic or metal blades, connectors to the dishwasher, system quietness, and more.
The barge then proceeded along the coast looking for another place to offload and continued to meet stiff resistance. The Mexican Navy denied it entrance to their waters. It made it as far south as Belize, again being rejected, before returning to New York.[2] Upon arrival it was met with a temporary restraining order and a heated legal battle preventing it from docking. In October, the trash was finally incinerated in Brooklyn and the resulting ash was buried where it originated, in Islip.[3][4]
This may result in higher costs for energy needed to supply oxygen in secondary operations. However, if the waste water treatment is finely controlled, the organic carbon in the food may help to keep the bacterial decomposition running, as carbon may be deficient in that process. This increased carbon serves as an inexpensive and continuous source of carbon necessary for biologic nutrient removal.[31]

Flip the disposer over and unscrew the electrical cover plate on the bottom of the disposer by removing the cover plate screw. Again, be sure the power to the unit has been turned off at the electrical supply panel. Then disconnect the electrical cable connector. Pull out the wires and remove the wire nuts. Also unscrew the ground wire from the green ground screw. Be sure to save the electrical cable connector so you can use it again.

Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.


Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Locate the circuit breaker that controls power to the garbage disposal, and flip it to the "off" position before continuing. Fix or replace the main seal if it is leaking. Remove both the drain pipe and the dishwasher hose, if applicable. Insert a screwdriver into the tightening ring and turn it counterclockwise. This will release the garbage disposal unit. Inspect the main seal that sits on the top of the unit. The seal is a large, soft rubber fitting that covers the top edge of the garbage disposal. If dirt, grit or food particles have fouled the main seal, wipe it down with a damp rag and reinstall the disposal unit. If the main seal is cracked, pitted or broken, it needs to be replaced. Once a new main seal has been inserted into the garbage disposal, push it up against the mounting bracket, insert a screwdriver into the tightening ring, and turn it clockwise to lock the unit into place. Reinstall the drain pipe and dishwasher hose, if applicable.
Make sure that there is power getting to the unit. Garbage disposals have an independent cord that is plugged into a wall socket beneath the sink. Unplug the disposal unit and plug another small appliance, like a desk fan, into the wall socket. Turn the appliance on to see if it works. If it doesn't work, check the breaker panel. If the breaker is flipped to the "On" position, there is an electrical problem on that circuit, and an electrician must be called in.
Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.
A broken garbage disposal makes tackling your to-dos an unnecessary challenge, which is why the experts at Sansone want to help. Whether your garbage disposal is leaking, clogged, humming, or completely stuck, we can repair the issue or replace your garbage disposal entirely. Contact us today with any plumbing questions or schedule an appointment that’s convenient for you by phone or on our website.
SquareTrade Protection Plans are only valid for new or Amazon certified refurbished products purchased at Amazon in the last 30 days. By purchasing this Protection Plan you agree to the Protection Plan Terms & Conditions (http://www.squaretrade.com/terms-standard). Your Protection Plan Terms & Conditions will be delivered via email within 24 hours of purchase

Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.
After watching this video, I decided I could replace my garbage disposer myself. Honestly, I think your site completely misrepresents how VERY difficult it is to hold up a 20+ pound disposal unit firmly up against the mounting hardware as you are literally crammed under your kitchen sink and then try and somehow get all three tabs to slide into place. I was very disappointed and, after 4 nights of trying and retrying, finally just called a plumber. Please don’t show anyone lifting something that is big and heavy and make it seems as light as a feather. Shame. Shame.

We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
Dispose orange peels, or any citrus rinds, to freshen the disposal and keep it smelling clean, but cut them into slices first as large pieces of citrus peel, e.g. half a lime, can jam a disposal. You can also use pieces of citrus fruit that may be too old to consume, as long as they're not too spoiled to smell nice. You can freeze these pieces first, if you wish.

If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.

If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Assuming that you have already given the disposal the time it needs to run and clear the garbage, you probably have a congested drain line. We don’t recommend using chemical drain cleaners with a garbage disposal. You will very likely just damage the unit and end up with a sink full of toxic chemicals that you’ll eventually be forced to clean out manually. If the blockage doesn’t go down with the good ol’ baking soda and vinegar remedy, then calling a John Moore professional is your best bet. He or she will know exactly how to properly remove the bolts, disconnect the drain trap and remove the trap and the discharge drain pipe, check for clogs and any other obstructions, and finally clear the blockage with the latest and best tools. (See our previous post about good steps you can take when your kitchen sink is clogged!)

In 1977, brothers Bob and Jim Gregory founded Texas Disposal Systems, Inc. with $10,000, one customer, one truck and plenty of determination. Building on a deep commitment to customer satisfaction and environmental preservation, the Gregory Family created a collection of businesses that has become one of the largest independently-owned solid waste collection and disposal companies in central Texas.
The Camorra first emerged during the chaotic power vacuum in the years between 1799 and 1815, when the Parthenopean Republic was proclaimed on the wave of the French Revolution and the Bourbon Restoration. The first official mention of the Camorra as an organization dates from 1820, when police records detail a disciplinary meeting of the Camorra, a tribunal known as the Gran Mamma. That year a first written statute, the frieno, was also discovered, indicating a stable organisational structure in the underworld. Another statute was discovered in 1842, including initiation rites and funds set aside for the families of those imprisoned. The organization was also known as the Bella Società Riformata, Società dell'Umirtà or Onorata Società.[9][10]
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
Modern garbage disposal units connect to dishwasher drainpipes.  This enables dishwashers to expel leftover food scraps and residue that would otherwise accumulate in the dishwasher unit.  A common source of leaks is the area where your dishwasher and garbage disposal connect.  These leaks most often occur when the hose’s clamp is not secure enough and when the dishwasher hose cracks.  To fix this issue, simply replace the cracked section of the hose or tighten the clamp.
Waste disposal units may jam, but can usually be cleared either by forcing the turntable round from above or by turning the motor using a hex-key wrench inserted into the motor shaft from below.[25] Especially hard objects accidentally or deliberately introduced, such as metal cutlery, can damage the waste disposal unit and become damaged themselves, although recent advances, such as swivel impellers, have been made to minimize such damage.[citation needed] More problematic are drain blockages caused by shredded waste that is fibrous, e.g., artichoke leaves, or starchy, e.g., potato peelings.
×