DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close

For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.


If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.

Warranty - The average industry warranty on a garbage disposal is one year; however, it is not uncommon to see manufacturers’ warranties that can extend up to ten years. As a general rule of thumb, the more comprehensive and longer a warranty is, the more confidence the manufacturer has in the product they have made, but this is not always the case, so it is still important to do your homework.


Locate the leak. Wipe off the disposal unit with a dry rag. Run water into the unit and turn it on. There are four places where the disposal unit may leak. At the top main seal, at the drain pipe, at the optional dishwasher inlet or along the garbage disposal body. Notice where the water is coming from. If the unit is wet at the very top, the main seal is leaking. If the area beneath the drain pipe is wet, the gasket is leaking. If the hose from the dishwasher feed drips, the hose or clamp may be faulty. If water is running out the bottom of the unit but the inlets and outlet are dry, the unit itself has developed a leak and must be replaced.
Dispose orange peels, or any citrus rinds, to freshen the disposal and keep it smelling clean, but cut them into slices first as large pieces of citrus peel, e.g. half a lime, can jam a disposal. You can also use pieces of citrus fruit that may be too old to consume, as long as they're not too spoiled to smell nice. You can freeze these pieces first, if you wish.
Call the plumbers at John Moore to take care of the issues for you if you aren’t sure how to do any repairs or maintenance yourself. As the saying goes, it’s better to be safe than sorry. We like to think that motto works every single time, so never be too embarrassed to ask us all your questions. We love to help! It’s what we do, and won’t ever stop doing.
Jump up ^ "Sub-committee onpo East-West Economic Co-operation and Convergence and Sub-committee on Civilian Security and Co-operation Trip Report: Visit to Rome / Palermo Secretariat Report 6–8 May 1998 (Prefect Gennaro Monaco, Deputy-Chief of Police and Chief of the Section of Criminal Police)". NATO Parliamentary Assembly. August 18, 1998. Retrieved 2009-01-24.

At one point, I did have a leak that I eventually determined was due to improper installation. (This was by the same "professional" plumber who reversed the hot and cold supply lines when installing a kitchen faucet. He just didn't connect the drain hose properly.) While investigating the issue, I called Waste King to inquire about possible in-home service or warranty replacement. I was blown away by their level of customer service: no waiting on hold, just an immediate connection to a person who really knew the product and was unexpectedly diligent in resolving my problem -- which, as it turns out, wasn't even their fault.
Flush with water. Simply flushing out the garbage disposal with water will help to remove any loose dirt or grime. Stopper the garbage disposal, add a squirt of dish soap and run the hot water until there is 2 to 4 inches (5.1 to 10.2 cm) sitting in the sink. Pull out the plug and turn on the garbage disposal, allowing the water to flush through.[2]
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
The size of the motor in the garbage disposal directly correlates to the units grinding ability. Garbage disposals typically have between 1/3-1 horsepower motors. Choose the correct horsepower based on the waste that you need to remove. 1/3 horsepower units will help tackle tasks like grinding vegetables easily, but more power is recommended if disposing a large quantity of food waste such as, vegetables and harder to grind meats.
Flush with water. Simply flushing out the garbage disposal with water will help to remove any loose dirt or grime. Stopper the garbage disposal, add a squirt of dish soap and run the hot water until there is 2 to 4 inches (5.1 to 10.2 cm) sitting in the sink. Pull out the plug and turn on the garbage disposal, allowing the water to flush through.[2]
To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
While you’re inspecting your drain lines, also look to see if you see wear and tear. Over the years, drain lines can sprout leaks and cracks that can lose water. If you notice that your lines look pretty worn, you may want to have them replaced. Again, if you are inexperienced with home improvement projects, it’s best to call a professional to tackle the job.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.

FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.


Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”
Your electrical supply wires should include a black (or hot) wire, a white (or neutral) wire and either a green or a bare wire, which is the ground wire. First remove the electrical cover plate on the bottom of the new disposer. Then move the new disposer into the cabinet. Screw the threaded end of the cable connector into the round hole on the bottom of the disposer. You’ll run your electrical supply wires through the cable connector and up through the access hole.

STEP 3 – Clear out the disposal to remove any bits of hard foods, bone shards or other fibrous gunk that may be preventing the grinding blades from rotating and pulverizing your discarded food. Use a tool (a pliers, wooden spoon, etc.) to do this. Putting your hand in situation where whirling blades of destruction are nearby is never a good idea. (That is what I’ve heard anyway.)

The best part about this common issue is that in most instances anyone can fix the problem regardless of their skill-set. Additionally, you won't necessarily have to purchase any tools in order to get your disposal back in working mode. Most disposals come with an Allen wrench attached to them which should be the only tool you may need to fix a humming garbage disposal.

In 2017, in Moscow and St. Petersburg, my research found a substantial increase in grassroots groups oriented around “civic pride” and local volunteer initiatives. These new groups focus on the preservation of green spaces, litter collection, recycling, urban beautification and historic preservation. These efforts represent a new “environmentalism of daily life” more acceptable to the government.

After using the lowest cost disposers for over 20 years now, I find the newest models have not withstood regular use for more than 5 years. The older models had a blue housing where this next step-up model has a black housing which I am hoping for at least 5 years use. Our oldest (blue housing) disposers have lasted at least 5 years and some are now almost 20 years old.

To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.
The snap ring fits into a groove on the lower end of the sink flange. When you’re working under the sink, it prevents the upper mounting bracket from falling off. Removing an old snap ring can be frustrating-unless you know this trick: Starting at the break in the ring, insert a thin-blade screwdriver between the ring and the flange. Pull down on the ring with the screwdriver’s blade and walk the blade around the ring. The ring will pop right off.
Even the most trustworthy garbage disposal will develop a leak from time to time; however, just because your food waste disposer has developed a leak does not necessarily mean that it needs to be replaced. Doing a little bit of investigating and troubleshooting before deciding to run out and buy a new garbage disposal can mean the difference between spending $10.00 for a replacement and $100.00+ to replace the entire unit.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
In 2017, in Moscow and St. Petersburg, my research found a substantial increase in grassroots groups oriented around “civic pride” and local volunteer initiatives. These new groups focus on the preservation of green spaces, litter collection, recycling, urban beautification and historic preservation. These efforts represent a new “environmentalism of daily life” more acceptable to the government.
2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.

Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.


After all this, if your garbage disposal still refuses to turn on, it’s likely just broken. The motor could be burned out or there could be another related problem. If that’s the case, now is the time to get a new unit. Contact a plumber for garbage disposal replacement. If you live in the Pittsburgh area, contact Terry’s Plumbing. We’ll be happy to come out to your home, diagnose the problem with your garbage disposal, and replace the unit if necessary. To find out more, call us today at (412) 364-9114.
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
Some towns and cities require a homeowner to get a permit before being allowed to install a new food disposal system. Others have outright outlawed the use of disposals due to limited sewer and water capacity. For example, an increasing number of cities in California has banned the installation of new garbage disposers in homes due to the ongoing drought the state is suffering from.
You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.

Garbage Disposal Install

×