If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.

If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
Jarred Connections: Considering the garbage-disposal systems is located under the kitchen sink, and since the area under the kitchen sink is a common place for storing all sorts of things, it is fairly common for the unit to get bumped.If it gets hit hard enough, the unit can actually shift so that it is no longer sitting straight. Pipes can also get knocked around, causing the seals to lose effectiveness.

Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
Assuming that you have already given the disposal the time it needs to run and clear the garbage, you probably have a congested drain line. We don’t recommend using chemical drain cleaners with a garbage disposal. You will very likely just damage the unit and end up with a sink full of toxic chemicals that you’ll eventually be forced to clean out manually. If the blockage doesn’t go down with the good ol’ baking soda and vinegar remedy, then calling a John Moore professional is your best bet. He or she will know exactly how to properly remove the bolts, disconnect the drain trap and remove the trap and the discharge drain pipe, check for clogs and any other obstructions, and finally clear the blockage with the latest and best tools. (See our previous post about good steps you can take when your kitchen sink is clogged!)

First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.


A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×