Compared to the Sicilian Mafia's pyramidal structure, the Camorra has more of a 'horizontal' than a 'vertical' structure. As a result, individual Camorra clans act independently of each other, and are more prone to feuding among themselves. This however makes the Camorra more resilient when top leaders are arrested or killed, with new clans and organizations germinating out of the stumps of old ones. As the Galasso clan boss Pasquale Galasso once stated in court; "Campania can get worse because you could cut into a Camorra group, but another ten could emerge from it."[27]
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
Horsepower Ratings – Even garbage disposals that have a basic ½ HP motor are more than capable of handling softer waste and bones; however, if your kitchen’s food waste routinely includes bones, cores, and harder vegetables, like carrots or avocados, then you need to look for a garbage disposal with a 1 HP (or higher) motor. A more powerful motor will be able to grind hard waste finer and faster, which reduces your chances of developing clogged pipes.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.
This part of the installation starts by removing the old mounting ring by loosening the mounting screws and then removing the snap ring, which holds the mounting assembly on the sink flange. You’ll need to use a flathead screwdriver to remove the snap ring. Next, remove the mounting ring by inserting the screwdriver into the tabs and turning the mounting ring assembly until it is free from the tabs. Be sure to support the bottom of the disposer as you do this. After this comes off, the entire mounting assembly will come free from the sink flange. Once free, pull the sink flange out from the top of the sink and scrape or wipe any old putty off the sink before wiping it clean with a towel.
One last thought - Beef bones? I see that Consumer Reports tests these things by measuring the fineness of the grind using beef bones. Do people really put beef bones down a garbage disposal on purpose? You might think I'm babying mine, or maybe that's why I didn't have excessive vibration when I use it, but I'll put the beef bones in the trash and grind up the rest of the stuff with this and be just fine for many years to come, I hope!

Chartered by entrepreneur Lowell Harrelson and Long Island mob boss Salvatore Avellino, it set sail on March 22 from Islip, New York,[2] escorted by the tugboat Break of Dawn and carrying 3,168 tons of trash headed for a pilot program in Morehead City, North Carolina, to be turned into methane. The barge was docked at Morehead City, until a WRAL-TV news crew, acting on a tip, flew by helicopter to the coast to investigate. Action News 5 Reporter Susan Brozek broke the story on the 6 p.m. news on April 1, 1987, and North Carolina officials began their own investigation, which resulted in an order for the Mobro to move on.


Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
The InSinkErator Badger 1 Continuous Feed Garbage Disposal 1/3 HP features a quick-mounting system that allows for easy installation or replacement. This sturdy garbage Disposal is constructed from galvanized steel and features a 26 oz. chamber for space-saving waste disposal. The garbage Disposal also features a 1/3 HP motor that rapidly grinds food waste for easy rinsing down the drain.

If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 


Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
Another method for cleaning and deodorizing your disposal unit is to sprinkle some baking soda in your unit and rinse it with about a cup of vinegar. This will create the bubbling “volcano effect” that kids love to watch so invite them in on this cleaning project. After allowing your mixture to sit for about 5 minutes, run hot water down the disposal until everything is thoroughly rinsed.
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

If you have a broken seal on the inside of your garbage disposal, you will see leaking coming from the bottom of your unit. Leaks that come from the bottom of your garbage disposal are usually attributed to cracks on the inside of the device. This is due to basic wear and tear overtime. To fix this issue, you’ll need simply invest in a new garbage disposal.
A garbage disposal unit (also known as a garbage disposal, waste disposal unit, garbage disposer, or in Canadian English a garburator) is a device, usually electrically powered, installed under a kitchen sink between the sink's drain and the trap. The disposal unit shreds food waste into pieces small enough—generally less than 2 mm (0.079 in)—to pass through plumbing.[1]
×