Running the garbage disposal without water or accidentally dropping items, such as flat wear or jewelry, can cause the disposal to jam. Food items, such as corn husks and potato skins, can also cause your disposal to jam. When the disposal motor jams, it can overheat quickly and cause the red button to pop from the bottom of the disposal. This stops the flow of electricity to protect the motor. When the reset button doesn’t work, you need to free the grinding plate or wall to release the jam.
If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 

The Camorra (Italian: [kaˈmɔrra]; Neapolitan: [kaˈmorrə]) is an Italian Mafia-type[2] crime syndicate, or secret society, which arose in the region of Campania and its capital Naples. It is one of the oldest and largest criminal organizations in Italy, dating back to the 17th century. Unlike the pyramidal structure of the Sicilian Mafia, the Camorra's organizational structure is more horizontal than vertical. Consequently, individual Camorra clans act independently of each other, and are more prone to feuding among themselves.
Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.
You can buy a 1/3-hp disposal for $80 or less, but our experts suggest that a more expensive unit with at least 3/4 hp would be a better choice. The more powerful the motor, the less chance it will jam. In addition, higher-priced disposals are generally quieter and have longer warranties. If you need to replace the splash guard guard as part of your garbage disposal installation, take a look at this guide.

We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.
However, whether the "high Camorra" was an integral part of the Camorra proper is disputed.[16] Although the inquiry did not prove specific collusion between the Camorra and politics, it brought to light the patronage mechanisms that fueled corruption in the municipality.[15] The society's influence was weakened which was exemplified by the defeat of all of their candidates in the 1901 Naples election. Many camorristi left for the United States in the early 20th century.[19]
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge.[32] The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).[33]
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.
I'm not what you'd call a handyman, although I've been working to get better at that. I will now at least try a home project before passing on it. So, when our 15-year garbage disposal died I had another opportunity. I determined our old unit to be a Badger 5 1/2 HP (this exact item). I didn't have time to wait for the item to arrive from Amazon so I went to Home Depot and coughed up an extra $20 for the Badger 500 - Home Depot's branded version of this item. They are identical except for the name & sticker.
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
After using the lowest cost disposers for over 20 years now, I find the newest models have not withstood regular use for more than 5 years. The older models had a blue housing where this next step-up model has a black housing which I am hoping for at least 5 years use. Our oldest (blue housing) disposers have lasted at least 5 years and some are now almost 20 years old.
STEP 4 – If you must use your hands (again, not advised) to pull out all that funky goo, see STEP 2. The disposal must be powered off and unplugged. No exceptions. Not even on a double-dog dare. Also, make sure your hand will actually fit into the opening so that you can eventually remove your hand from the opening. You may need your hand later. If you think it is going to be a tight fit, I’d suggest that you not try it all. You’ve been warned.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.
This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close
Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.
Sometimes plumbing problems are better left to the professionals, which is why Sansone is proud to offer quality plumbing products and plumbing services at economical pricing. Whether you’re in need of garbage disposal repair or replacement, hot water heater service or more, we have got you covered. Contact us today to learn more about our great services or schedule your appointment online.
The easiest way to apply that force is to squeeze them together using tongue-and-groove pliers, such as Channellocks. You’ll need medium or large pliers to do this. Unlike prying on the lower ring with a screwdriver or hex wrench-the method recommended in most instruction sheets-squeezing can’t disturb the position of the sink flange and cause it to leak. Plus, it’s easier on the wrists.
At one point, I did have a leak that I eventually determined was due to improper installation. (This was by the same "professional" plumber who reversed the hot and cold supply lines when installing a kitchen faucet. He just didn't connect the drain hose properly.) While investigating the issue, I called Waste King to inquire about possible in-home service or warranty replacement. I was blown away by their level of customer service: no waiting on hold, just an immediate connection to a person who really knew the product and was unexpectedly diligent in resolving my problem -- which, as it turns out, wasn't even their fault.

In the event that you do not have a grounded outlet to power the garbage disposal, you will need to install one. Adding a grounded outlet may cost as little as $5 when existing electrical wiring is placed a short distance away, plus an additional $75 for the electrician's labor. If a new grounded outlet needs to be added and electrical wiring does not yet exist, it will likely cost around $90, depending on labor and parts. If your project requires the addition of a new switch and wire, plan to spend an average of $5 to $10 on materials, plus about 30 minutes of labor at an average cost of $75 an hour.
The origins of the Camorra are not entirely clear. It may date back to the 17th century as a direct Italian descendant of a Spanish secret society, the Garduña, founded in 1417. Officials of the Kingdom of Naples may have introduced the organization to the area, or it may have grown gradually out of small criminal gangs operating in Neapolitan society near the end of the 18th century.[3] However, recent historical research in Spain suggests that the Garduña never really existed and was based on a fictional 19th century book.[4]

Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
Some towns and cities require a homeowner to get a permit before being allowed to install a new food disposal system. Others have outright outlawed the use of disposals due to limited sewer and water capacity. For example, an increasing number of cities in California has banned the installation of new garbage disposers in homes due to the ongoing drought the state is suffering from.

Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.
Don’t you wish good things could last forever? You’ve been there. We have, too. But the reality is that things don’t usually go the way we plan. When you least expect it, life throws a curve ball your way. The way kitchen appliances work is no different, and that especially means the ones we use every day. Garbage disposals are an essential kitchen convenience for most homeowners that are used pretty much every day. Prepping food and cooking becomes much easier when peels and other scraps can just be tossed into the sink and straight down the drain, but over time, all that will take its toll.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]

Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.


How many years do garbage disposals last? One the average, quite a long time. In fact, with adequate care and proper maintenance, garbage disposal units can be of good service for about 8 to 15 years. This means the blades remain efficient and the motor has not burned out yet. This being said, neglecting garbage disposal leaks will significantly decrease this effective service life.


Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.

Garbage Disposal Repair

×