Waste disposal units may jam, but can usually be cleared either by forcing the turntable round from above or by turning the motor using a hex-key wrench inserted into the motor shaft from below. Especially hard objects accidentally or deliberately introduced, such as metal cutlery, can damage the waste disposal unit and become damaged themselves, although recent advances, such as swivel impellers, have been made to minimize such damage. More problematic are drain blockages caused by shredded waste that is fibrous, e.g., artichoke leaves, or starchy, e.g., potato peelings.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.
Turn off the garbage disposal at the breaker box. Remove the drain pipe if it is leaking there. Most attachment clamps are wire clamps with two protruding wires that are pushed together to release the drain pipe. Push the wires together and remove the clamp. Pull the pipe off and inspect the seal for any debris that may have lodged between the seal and the pipe. Wipe the seal with a damp rag to remove any dirt, debris or food particles. Sometimes the wire clamp loses tension. In that case, tighten the hose clamp down in its place, which may secure the pipe leak-free.
After you install the new sink flange, you don’t want it shifting around when you’re assembling the parts underneath. Movement of the flange could break the seal between the flange and the sink, inviting a leak. Your best bet is to ask a helper to press down on the sink flange, or if you’re working alone, find something to weigh it down, such as the old disposal. Place an old towel under the weight so you don’t scratch the sink. If the bottom of your sink is quite concave, the old disposal might not contact the flange. In that case, place a can on the flange, then weigh down the can.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
In the 1970s and 1980s Raffaele Cutolo made an attempt to unify the Camorra families in the manner of the Sicilian Mafia, by forming the New Organized Camorra (Nuova Camorra Organizzata or NCO), but this proved unsuccessful. Drive-by shootings by camorristi often result in casualties among the local population, but such episodes are often difficult to investigate because of widespread omertà (code of silence). According to a report from Confesercenti, the second-largest Italian Trade Organization, published on October 22, 2007 in the Corriere della Sera, the Camorra control the milk and fish industries, the coffee trade, and over 2,500 bakeries in Naples.
The majority of today’s garbage disposals are designed to dovetail with a sink’s drain outlet, which makes connecting the two components simple. There are a multitude of connection kits and adaptors available. Many models feature a power cord that is simply plugged into a nearby outlet to power the unit; however, when an outlet is not available, the unit must be hardwired, which can be significantly more expensive.
One of the handiest appliances in your kitchen is probably something that you don’t think about very often, until it stops working. It’s your garbage disposer, and today I’m going to show you how to replace a garbage disposer under your kitchen sink. This project requires some moderate do-it-yourself skills, and it also requires turning off the electricity to the disposer at the electrical panel. But it’s really not that difficult, so let’s get started.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
SquareTrade Protection Plans are only valid for new or Amazon certified refurbished products purchased at Amazon in the last 30 days. By purchasing this Protection Plan you agree to the Protection Plan Terms & Conditions (http://www.squaretrade.com/terms-standard). Your Protection Plan Terms & Conditions will be delivered via email within 24 hours of purchase
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.