If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.

If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.
When rubber gaskets age, they can develop leaks. The gasket can dry up, crack, and leak when it is repeatedly exposed to long periods of disuse where no water is present in the drain pipe. Should an older garbage disposal be removed and then placed back, it will require a new rubber gasket to again achieve a watertight seal. Moreover, if a gasket is not evenly locked on all three sides, then it will develop a leak.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
At the time, the Mobro 4000 incident was widely cited by environmentalists and the media as emblematic of the solid-waste disposal crisis in the United States due to a shortage of landfill space: almost 3,000 municipal landfills had closed between 1982 and 1987.[5] It triggered much national public discussion about waste disposal, and may have been a factor in increased recycling rates in the late 1980s and after.[6] It was this that caused it to be included in an episode of Penn & Teller: Bullshit! (season 2, episode 5) in which they debunk many recycling myths.
"Thank you for creating a product that will help reduce the need to call a plumber every 2-3 weeks. I have tried various options to get my staff to take better care of what goes down the 3 compartment sink drain but it did not work. The Drain Strainer makes it extremely simple for them. The first two XL's that I ordered have worked perfectly. These additional two I ordered are for a different location and we expect the same results there." Jim Abanto - Owner El Chalan Restaurant - Miami FL
No need to worry if your garbage disposal is on the fritz—installing a new one is a straightforward project that you can do yourself in just a few minutes. Start by switching off the power to the disposal at your home’s breaker box to ensure that you can work safely. Next, remove the old unit by detaching it from the mounting ring directly beneath the sink drain. Finally, install any necessary new mounting hardware, fit the new disposal into place, and turn on the water to test for leaks before giving it a trial run.
Built-in trash compactors fit snuggly into your kitchen cabinetry. Having a built-in compactor means you have one less appliance occupying precious floor space. A convenient toe pedal opener lifts the top open for easy hands-free opening, and a removable drawer make it easy to clean and empty the compactor. Shop for new garbage disposals and trash compactors from JCPenney today!
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).

Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.


If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
A continuous feed model features a switch that is generally mounted on the wall nearby. In rarer cases, an air pressure switch may be mounted on the countertop. These air pressure switches are considered safer than traditional flip switches because they guard against shock by isolating the electrical system away from the sink’s source of water. Batch feed garbage disposals do not require the installation or use of a switch. Safety codes in your community will dictate how far away from the sink the electrical switch must be located.
Reattach the electrical wires. Unscrew the faceplate on the underside of the new unit. Match the colored wires on the power supply to those in the disposal’s electric housing and connect them using plastic wire nuts. Slip the copper grounding wire over the green screw at the far edge of the compartment. Replace the cover and tighten the screws.[16]
We won’t sugar-coat it. This one is the doozy. If the leak is located at the bottom of the unit that means at least one internal seal has slipped, chipped, or flat-out deteriorated. The catch is, there are lots of these seals inside the disposal, and if one has failed it means the others are on their way. You can replace these seals with expensive, original equipment manufacturer (OEM) parts – or you can just get a new garbage disposal.

Jump up ^ "Sub-committee onpo East-West Economic Co-operation and Convergence and Sub-committee on Civilian Security and Co-operation Trip Report: Visit to Rome / Palermo Secretariat Report 6–8 May 1998 (Prefect Gennaro Monaco, Deputy-Chief of Police and Chief of the Section of Criminal Police)". NATO Parliamentary Assembly. August 18, 1998. Retrieved 2009-01-24.
Many Camorra members and associates fled the internecine gang warfare and Italian Justice and immigrated to the United States in the 1980s. In 1993, the FBI estimated that there were 200 camorristi in the United States. Although there appears to be no clan structure in the United States, Camorra members have established a presence in Los Angeles, New York and Springfield, Massachusetts.[56] The Camorra is the least active of all the organized crime groups in the United States.[57] In spite of this, the US law enforcement considers the Camorra to be a rising criminal enterprise, especially dangerous because of its ability to adapt to new trends and forge new alliances with other criminal organizations.[58]
Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
×