Garbage disposals help us get rid of food waste, so it’s not surprising that the appliance may be susceptible to gross smells. A capful of bleach or grinding up citrus peels can help eliminate any foul odors coming from your garbage disposal. However, if nothing seems to help your appliance in the smell department, it may be catching food particles within its crevices. We recommend disassembling your garbage disposal to clean it, or replacing it if it’s old.

Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]

Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.
However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.

Start by turning off and unplugging the garbage disposal. Next, you’ll need the wrench that came with your disposal. If you don’t have it, you can buy a replacement in a hardware store that sells your disposal brand. Find the hex-shaped opening at the bottom of the disposal unit. Turn the wrench clockwise to dislodge whatever’s blocking the flywheel. When the object dislodges, you’ll feel the flywheel start to turn easily. Reset the disposal and run cold water while quickly turning it on and off repeatedly.
If the disposal jams, turn off the power and look underneath the sink. There is a place in the center of the motor shaft, on the bottom of the unit, where you can use an allen wrench to manually turn the motor. Give the motor a few manual turns to get it unstuck. Remove the Allen wrench before you try to run the motor again. Also, press the reset button/ circuit breaker on the bottom of unit, if applicable.
Inspect each of these locations while gliding a light-colored rag over the unit; the dyed water will readily show on the rag and reveal the location of the leak. If a leak isn’t immediately apparent, remove the sink stopper and pour a few more cups of dyed water down the sink drain, then check for leaks again. Leaks near the top of the unit are more likely to show themselves while the sink is plugged, while side and bottom leaks are more noticeable while the sink is unplugged.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
A broken garbage disposal makes tackling your to-dos an unnecessary challenge, which is why the experts at Sansone want to help. Whether your garbage disposal is leaking, clogged, humming, or completely stuck, we can repair the issue or replace your garbage disposal entirely. Contact us today with any plumbing questions or schedule an appointment that’s convenient for you by phone or on our website.
To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.
Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes ... full review
So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.

Prior to testing the garbage disposal for leaks, unplug it at the wall outlet and turn off the power from the breaker box to prevent electrical shock. Then insert a watertight sink stopper into your sink drain and wipe the unit dry with a clean cloth. In any handy container, mix a few drops of food coloring into a few cups of water, and pour the dyed water onto the sink stopper to help you locate the leak.


However, homeowners are often cautioned against using caustic drain cleaners. Some professional plumber believe that it will not always remove clogs and may even be quite harmful. The caustic nature of this and similar products should be a cause for concern because aside from not really needing it, the ingredients known as lye or caustic soda can result in severe burns and may cause damage to the pipes.
The company Waited hired has an “A plus” rating with the Better Business Bureau and has been in business for 14 years. They didn’t do anything wrong, so CBS4 is not naming them. They didn’t want to discuss the charges. They stand behind their billing, but they didn’t like having a customer who was unsatisfied. The company agreed to refund $400 to Waite.
Kitchen garbage disposals are wondrous appliances, helping to clean away unwanted food scraps in a jiffy. Even though they are normally self-cleaning, garbage disposals need a little love and attention from time to time. This keeps them in tip-top condition and prevents odors from forming. This article will provide you with easy step-by-step instructions on how to safely clean your garbage disposal and effectively eliminate odors, while also providing some useful info on garbage disposal maintenance.

The barge then proceeded along the coast looking for another place to offload and continued to meet stiff resistance. The Mexican Navy denied it entrance to their waters. It made it as far south as Belize, again being rejected, before returning to New York.[2] Upon arrival it was met with a temporary restraining order and a heated legal battle preventing it from docking. In October, the trash was finally incinerated in Brooklyn and the resulting ash was buried where it originated, in Islip.[3][4]
First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.
Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
Thank you for sharing this tutorial. My husband and I tried to fix our garbage disposal last week but we couldn’t get it to work. When we turn it on, it makes a humming noise, but nothing is blocking the blades. We might need to get a new disposal, but we’ll probably have a professional look at it before we decide. We’ll keep your tips on hand, just in case.
Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.

When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.


Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
As I have mentioned, garbage disposers for most people are just another kitchen appliance that we tend to take for granted, and this is one of the reasons I decided to bring this website to the internet. I have come across many customers over the years that only seem to notice this “gadget” when it goes wrong, and believe it or not, most of the time they go wrong is because they’re not cared for properly.
Fixing a leaky sink flange may be very easy. It could be a simple matter of tightening the bolts that hold the flange onto the sink drain. But if that doesn’t work, you may need to apply a new layer of plumbers putty to seal the flange into place. To do this, you’ll need to loosen the mounting bolts and create enough space between the flange and drain to smear a fresh dab of putty all the way around the drain. Then just re-tighten the bolts and wait a few hours for the putty to form a tight seal.

Has this ever happened to you? It’s the end of the day and you are dutifully washing your evening dishes.  Your sink isn’t draining quickly, so you flip on the switch of your waste disposer expecting to hear the satisfying sound of your meal remnants being ground into a pulp.  Instead – to your shock and dismay – the disposal only hums, or even worse, does nothing at all. Frustrating, right?
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)
Throw some ice down once in a while. While ice will not sharpen the shredders (as is commonly believed) it does knock off any debris buildup on the sharp edges that keeps them from grinding food properly. For better results, make special ice cubes from pure lemon juice or vinegar, or alternate with biodegradable cleanser (label them in your freezer!) Cover and seal ice trays used in your freezer for cleanser, and do not reuse trays for food or drink after having been used for cleanser. While using the disposal, be sure to run cold water at the same time.
The size of the motor in the garbage disposal directly correlates to the units grinding ability. Garbage disposals typically have between 1/3-1 horsepower motors. Choose the correct horsepower based on the waste that you need to remove. 1/3 horsepower units will help tackle tasks like grinding vegetables easily, but more power is recommended if disposing a large quantity of food waste such as, vegetables and harder to grind meats.

Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).


But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.
A continuous feed model features a switch that is generally mounted on the wall nearby. In rarer cases, an air pressure switch may be mounted on the countertop. These air pressure switches are considered safer than traditional flip switches because they guard against shock by isolating the electrical system away from the sink’s source of water. Batch feed garbage disposals do not require the installation or use of a switch. Safety codes in your community will dictate how far away from the sink the electrical switch must be located.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)
First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.
One of the handiest appliances in your kitchen is probably something that you don’t think about very often, until it stops working. It’s your garbage disposer, and today I’m going to show you how to replace a garbage disposer under your kitchen sink. This project requires some moderate do-it-yourself skills, and it also requires turning off the electricity to the disposer at the electrical panel. But it’s really not that difficult, so let’s get started.
If this sounds familiar, you'll be happy to know that replacing a disposer is really fairly simple. With today's plastic waste kits, leaks are seldom a problem and the electrical connections are similarly quick and easy. Finally, retail outlets sell good disposers for every household budget. Before you buy, though, it pays to check out your old unit to make sure it's not simply jammed.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
Many Camorra members and associates fled the internecine gang warfare and Italian Justice and immigrated to the United States in the 1980s. In 1993, the FBI estimated that there were 200 camorristi in the United States. Although there appears to be no clan structure in the United States, Camorra members have established a presence in Los Angeles, New York and Springfield, Massachusetts.[56] The Camorra is the least active of all the organized crime groups in the United States.[57] In spite of this, the US law enforcement considers the Camorra to be a rising criminal enterprise, especially dangerous because of its ability to adapt to new trends and forge new alliances with other criminal organizations.[58]
One of the Camorra's strategies to gain social prestige is political patronage. The family clans became the preferred interlocutors of local politicians and public officials, because of their grip on the community. In turn, the family bosses used their political sway to assist and protect their clients against the local authorities. Through a mixture of brute force, political status, and social leadership, the Camorra family clans imposed themselves as middlemen between the local community and bureaucrats and politicians at the national level. They granted privileges and protection, and intervened in favour of their clients in return for their silence and connivance against local authorities and the police. With their political connections, the heads of the major Neapolitan families became power brokers in local and national political contexts, providing Neapolitan politicians with broad electoral support, and in return receiving benefits for their constituency.[26]
This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×