DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
If you misplaced your wrench that came with the unit, don’t worry. The store you got your unit from should have replacements for as little as $3 to $5. An Allen wrench will usually work well, too. Replacing the motor is the most costly repair for a disposal, so replacing the unit may be your best bet. If the disposal is jammed and won’t budge after using your wrench, turn it off and call us right away.
There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Garbage disposals with stainless steel grinding blades and turntables make easy work of leftover meatloaf and biscuits. These blades will stay strong and last for years. High-power grinding motors hit maximum speeds quickly. This means jams and clogs are less likely to happen. Make sure to keep the faucet running for about 60 seconds after you turn off the disposal. Doing this ensures that all of the food particles make it down the hose.

STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.
In most cases if your garbage disposal is humming it is because a foreign object is stuck in the disposal. If an item has been jammed in the blades of the disposal they will be unable to rotate. This can result in a humming noise. If this is the case simply unplug the disposal under the sink then survey the drain hole. If you discover that an object is stuck in the blades remove it. Once you have done this you can plug the disposal back in and flip the switch. This should clear up the problem.
Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).

Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]
In the 1970s, the Sicilian Mafia convinced the Camorra to convert their cigarette smuggling routes into drug smuggling routes with the Sicilian Mafia's assistance. Not all Camorra leaders agreed, leading to the Camorra Wars that cost 400 lives. Opponents of drug trafficking lost the war. The Camorra made a fortune in reconstruction after an earthquake ravaged the Campania region in 1980. Now it specializes in cigarette smuggling and receives payoffs from other criminal groups for any cigarette traffic through Italy. The Camorra is also involved in money laundering, extortion, alien smuggling, robbery, blackmail, kidnapping, political corruption, and counterfeiting. It is believed that nearly 200 Camorra affiliates reside in this country, many of whom arrived during the Camorra Wars.[59]
Safety and vigilance are paramount with these disposals. If you have small children in your home, then you must be on your guard to ensure that they do not stick their hands or other small objects down the disposal. You must also be careful to ensure that you do not accidentally drop any foreign objects down the disposal. For example, if a spoon were to fall into the disposal, and the disposal was turned on, it could cause quite a bit of damage to the unit before you are able to fish it out.
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.
As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.

Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.
In 2008, Italian police arrested three members of the Camorra crime syndicate on September 30, 2008. According to Gianfrancesco Siazzu, commander of the Carabinieri police, the three were captured in small villas on the coast of Naples. All three had been on Italy's 100 top most wanted list. Police seized assets valued at over 100 million euros and also weapons, including two AK-47 assault rifles that may have been used in the shooting of six Africans on September 18, 2008. Police found pistols, Carabinieri uniforms and other outfits that were used to disguise members of the operation. During the same week, a separate operation netted 26 additional suspects in Caserta. All were believed to belong to the powerful Camorra crime syndicate that operates in and around Naples. The suspects were charged with extortion and weapons possession. In some cases, the charges also included murder and robbery. Giuseppina Nappa, the 48-year-old wife of a jailed crime boss, was among those arrested. She is believed to be the Camorra's local paymaster.[46]
This is our workhorse medium-capacity model with a This is our workhorse medium-capacity model with a powerful 2 HP motor that handles hundreds of servings at one meal. Like all InSinkErator foodservice disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as schools hospitals larger restaurants ...  More + Product Details Close
But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.
Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.
The mounting bracket for your new garbage disposer assembles by inserting the fiber gasket, back-up flange and mounting ring over the sink flange, in that order. Be sure to hold these three pieces in place while you insert the snap ring over the flange. It’s called a snap ring because you’ll hear it snap in place. Then firmly tighten the three mounting screws against the backup flange, being careful to tighten them evenly.
If the disposal’s still leaking, loosen the mounting bolts and push the sink flange up until it’s slightly higher than the surface of the sink. Apply fresh plumber’s putty to the threshold between the flange and the sink. When you’ve applied enough, re-attach the unit by putting the bolts back and tightening. Wipe away excess putty that squeezed out. Finish re-installing by replacing the disposal unit on the mount. Turn the disposal back on and look for leaks.
Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
Loosen the nut securing the rest of the assembly. Just below the sink flange where the drain empties into the garbage disposal you’ll see a circular plastic piece similar in appearance to the mounting ring. Insert the tip of a screwdriver into one of the lugs on this piece and rotate it in a counterclockwise direction. Pull the nut away and set it aside.[9]
The 2 800 RPM motor-powered dual stainless-steel swivel The 2 800 RPM motor-powered dual stainless-steel swivel impellers built into this GE 1/2 HP Continuous-Feed Garbage Disposal join forces with a 2-level pre-cutter to make it easy to grind undesirable waste into easily drainable particles. The disposer's large-capacity disposer chamber is comprised of a cold-rolled carbon steel armature shaft ...  More + Product Details Close
Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.

The origins of the Camorra are not entirely clear. It may date back to the 17th century as a direct Italian descendant of a Spanish secret society, the Garduña, founded in 1417. Officials of the Kingdom of Naples may have introduced the organization to the area, or it may have grown gradually out of small criminal gangs operating in Neapolitan society near the end of the 18th century.[3] However, recent historical research in Spain suggests that the Garduña never really existed and was based on a fictional 19th century book.[4]
Run your garbage disposal for longer each time you use it. A mistake many people make is turning off their garbage disposal as soon as the grinding noises stop. It is better to leave the garbage disposal on (with the water running) for several seconds after the grinding noises subside, as there may still be small particles in the disposal unit which have not yet been cleared away.
Garbage disposals can range from $70 on the low end to $380 on the high end -- and generally speaking, you get what you pay for. A less expensive unit is likely to produce more noise, require more water, and clog more easily than a higher-end model. Likewise, a more expensive unit will be faster, quieter and less likely to malfunction than a lower end model -- and it will be lighter-weight and offer greater capacity as well. The average cost of a garbage disposal installation with a one-year manufacturer’'s warranty is $185. The average amount of time taken to install a garbage disposal, including cleanup, is three hours. The hourly cost for labor will range from $20 to $40 -- $28 on average.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
×