If the unit is hardwired to the house then you have to use a screwdriver to remove the plate covering the wire connections on the disposal. Disconnect the exposed wires and then remove the plate covering the junction box on the wall. Untwist the wire caps securing the disposal wires to your home wires and set the disposal’s wires on the side. Twist the wire capes over the exposed wires in the junction box, put the wires into the junction box and reattach the junction box plate.
If the leak occurred in either of the two connections (smaller = dishwasher, larger = sewer) exiting the side of your disposal unit, it’s a pretty straightforward fix. Loosen the metal clamps on these hoses and make sure the rubber gaskets inside are not falling apart. If needed, replace these gaskets. Reattach the hoses and re-clamp the connections with new metal clamps.

When you buy a new disposal, the box will contain all the parts you need to install it. Before you jump into removing the old unit, take a few moments to familiarize yourself with all these parts. Put them together in the correct order and try out the locking mechanism. Understanding how everything fits together ahead of time will make the job a cinch.
Garbage disposals aren’t exactly quiet, but the device shouldn’t make a terrible screeching noise either. If your appliance is guilty of shrill sounds, there are a few potential causes. The grates could have shifted causing the device to move incorrectly, or the motor could be worn out. In either case, this usually occurs when a garbage disposal is at the end of its life, so replacement is a good option.
To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.

The InSinkErator Badger 1 Continuous Feed Garbage Disposal 1/3 HP features a quick-mounting system that allows for easy installation or replacement. This sturdy garbage Disposal is constructed from galvanized steel and features a 26 oz. chamber for space-saving waste disposal. The garbage Disposal also features a 1/3 HP motor that rapidly grinds food waste for easy rinsing down the drain.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.

In the United States, almost all garbage disposals on the market are manufactured by a handful of companies; although, many are branded under different names. For example, out of the top ten highest rated models on the market, InSinkErator makes eight of them. Whirlpool and WasteKing are the other two most well-known brands in the U.S. There are a wide range of models to choose from, ranging from basic $50.00 models to models equipped with all of the latest bells and whistles that can cost as much as $600.00. In most cases, you get what you pay for in terms of quality. Here is a brief overview of the top brands in the U.S.
The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
As it's a direct replacement, I didn't even bother to go through the hassle or removing the old sink flange and having to putty in a new one as the existing one was just fine. It took me about 5 minutes to replace old with new - that's why I didn't bother with a different make. I'm an average Joe who does a few things around the house - mostly accompanied by a lot of cussing - so anything that makes such work quick and simple results in less swearing - which is a good thing right?!

Some types of food remains are not easy to grind in a disposer. Do not put fibrous food items into your disposal. Help grind these items by putting in a few small bones or large ice cubes to the disposal. If the disposer won’t grind it up then turn off the disposer and remove the item with a pair of tongs. When using your disposer, make sure that the disposal is running with good water flow. Good water flow carries the waste down the drain line. Using too little water can create a clogged drain.


Disposals can leak at a couple different places. Start by turning off the disposal at its base. Then, find the disposal mount and remove the unit by turning it counterclockwise from the bottom. Once the disposal has been removed from the mount, you should be able to see the three mounting bolts. Tighten these bolts to make sure they’re not leaking.

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.


Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
Warranty - The average industry warranty on a garbage disposal is one year; however, it is not uncommon to see manufacturers’ warranties that can extend up to ten years. As a general rule of thumb, the more comprehensive and longer a warranty is, the more confidence the manufacturer has in the product they have made, but this is not always the case, so it is still important to do your homework.
To reseal the leaky flange, you must first detach the garbage disposal. Start by loosening the screws securing the main drain pipe to the disposal, then loosen the screws in the metal clamp securing the dishwasher hose to the disposal and detach the drain pipe and dishwasher hose from the disposal. Loosen the screws in the mounting ring that connects the disposal to the metal mounting assembly beneath the sink, then pull down the disposal and carefully set it on a clean, dry surface. Loosen the bolts in the mounting assembly with a wrench, then pull down the mounting assembly and set it near the disposal.
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.

The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.
Dishwasher Connection: Some disposals are connected to the dishwasher drain pipe, which drains leftover food removed from dishes going through the wash cycle. Leaks can sometimes occur in the hose connections where the disposal hose attaches to the dishwasher.Leaks can also happen if the seal on the hose is compromised or the clamp on the hose isn’t tight enough. If the connecting hose seems to be the source of the leak, try tightening the connection or replacing the seal. If neither solutions work, or the hose is obviously cracked, you will need to replace the hose.
A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
As a general rule of thumb, the heavier and bigger that a garbage disposal is, the more quietly it will operate – so long as it fits properly underneath your sink. Even though the sound dampening technology used in the design of garbage disposals has improved dramatically in the last 10 years, it is unrealistic to expect your garbage disposal to operate noise free. Under specific sinks, some disposals will be noisier than others due to the amount of vibration they produce. Ideally, you should look for a garbage disposal that features a nylon, insulated grinding chamber, like those produced by WasteKing.
Read the directions for your model before attempting a home repair. Most disposals have an electrical reset button, and a manual hex key for un-jamming. If the disposal stops working, its internal circuit breaker may have shut it off. Turn the switch definitely off, and try to pull out the hard object that may have jammed it. Then use the right-sized hex key to manually turn the rotor parts (usually directly under the unit in the center). If it turns, then push the reset button. It usually clicks in. Then, turn on the water and try the power, again.
My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.
If your disposal grinds poorly, make sure that you are running enough water while operating the unit and that you are not grinding matter that you shouldn’t. If you can hear the garbage disposal running but it is not grinding, the blades may be broken. It’s usually easier and cheaper to just replace the entire unit. See How to Install a Garbage Disposal.
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
Knowing the difference between what can go down the disposal and what should go into the trash can save you an emergency call to the plumber. This is especially pertinent during the holidays when the kitchen is filled with people and the sink with dirty dishes. Practice these three everyday maintenance tips to help you maximize the lifespan of your garbage disposal.
Dishwasher Connection: Some disposals are connected to the dishwasher drain pipe, which drains leftover food removed from dishes going through the wash cycle. Leaks can sometimes occur in the hose connections where the disposal hose attaches to the dishwasher.Leaks can also happen if the seal on the hose is compromised or the clamp on the hose isn’t tight enough. If the connecting hose seems to be the source of the leak, try tightening the connection or replacing the seal. If neither solutions work, or the hose is obviously cracked, you will need to replace the hose.

While you’re inspecting your drain lines, also look to see if you see wear and tear. Over the years, drain lines can sprout leaks and cracks that can lose water. If you notice that your lines look pretty worn, you may want to have them replaced. Again, if you are inexperienced with home improvement projects, it’s best to call a professional to tackle the job.
Garbage protests in Volokolamsk and elsewhere have exposed weaknesses in Russia’s system of political authority, often described as a “power vertical” in which government officials answer not to their constituents, but to their political superiors and ultimately to President Putin. Facing unresponsive or incompetent officials, citizens turn to Putin as the only one who can solve their problems.
Badger Series garbage disposals are the choice of homeowners looking for hard-working helpers in the kitchen that are as tough on food waste as they are easy on the wallet. The value and price is unbeatable. A powerful, 1/2 HP Dura-Drive motor powers the Badger 5 through your food waste including: vegetables, fruits, leftovers, egg shells, celery stalks, and small bones.
Horsepower Ratings – Even garbage disposals that have a basic ½ HP motor are more than capable of handling softer waste and bones; however, if your kitchen’s food waste routinely includes bones, cores, and harder vegetables, like carrots or avocados, then you need to look for a garbage disposal with a 1 HP (or higher) motor. A more powerful motor will be able to grind hard waste finer and faster, which reduces your chances of developing clogged pipes.
Garbage disposals help us get rid of food waste, so it’s not surprising that the appliance may be susceptible to gross smells. A capful of bleach or grinding up citrus peels can help eliminate any foul odors coming from your garbage disposal. However, if nothing seems to help your appliance in the smell department, it may be catching food particles within its crevices. We recommend disassembling your garbage disposal to clean it, or replacing it if it’s old.
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.
×