Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.

No need to worry if your garbage disposal is on the fritz—installing a new one is a straightforward project that you can do yourself in just a few minutes. Start by switching off the power to the disposal at your home’s breaker box to ensure that you can work safely. Next, remove the old unit by detaching it from the mounting ring directly beneath the sink drain. Finally, install any necessary new mounting hardware, fit the new disposal into place, and turn on the water to test for leaks before giving it a trial run.
Since the mid-1990s, the Camorra has taken over the handling of refuse disposal in the region of Campania, with disastrous results for the environment and the health of the general population. Heavy metals, industrial waste, chemicals and household garbage are frequently mixed together, then dumped near roads and burnt to avoid detection, leading to severe soil and air pollution.
Our testers found that differentiating features you'll typically see at the store may not deliver the durability they imply. We also found that some models with fewer features and a shorter warranty cost more than relatively similar competitors. Home garbage disposers typically last about 10 to 12 years, according to InSinkErator, though not all reach the decade mark. A longer warranty does not guarantee longer life and can also make some models cost more than otherwise-similar machines. Here are the garbage disposer features to consider:

As it's a direct replacement, I didn't even bother to go through the hassle or removing the old sink flange and having to putty in a new one as the existing one was just fine. It took me about 5 minutes to replace old with new - that's why I didn't bother with a different make. I'm an average Joe who does a few things around the house - mostly accompanied by a lot of cussing - so anything that makes such work quick and simple results in less swearing - which is a good thing right?!

My old built in guard got destroyed over the years. Rather than remove the whole disposal I ordered this, hoping it would solve the problem of the noise and the water and food particles that would fly out of the disposal onto my slightly hairy chest and face. This solved both problems. It is so quiet that it is like white noise. Such a calming sound that you can sleep to it.
In the event that you do not have a grounded outlet to power the garbage disposal, you will need to install one. Adding a grounded outlet may cost as little as $5 when existing electrical wiring is placed a short distance away, plus an additional $75 for the electrician's labor. If a new grounded outlet needs to be added and electrical wiring does not yet exist, it will likely cost around $90, depending on labor and parts. If your project requires the addition of a new switch and wire, plan to spend an average of $5 to $10 on materials, plus about 30 minutes of labor at an average cost of $75 an hour.
I hope this helps someone and encourages others to get the product. I think it is a great product and many of the poor reviews are because people didn't know how to use the mounting system. I gave it 4 stars because it doesn't have any tips in trouble shooting for when it leaks out the bottom. It should at least say to look at the drain hose and that it may be leaking inside from there and only appear to be leaking from the bottom. I also think Waste King should have made a video to show the EZ mount system. I mean it took me less than 10min. to do it all. Lastly, I don't like the click it can make when it turns on. While lots of people mention this and the directions say it's normal it is not "standard" in the garbage disposal business, meaning most don't make this noise. It can be startling and sound like something metal is in your disposal. While it is normal for their units, I still don't like it. It will take getting used to and then what if something metal is in my disposal will I think there isn't and that it's the click. That could cause damage very quickly if I think it's nothing and it is something.
Bathroom Plumbing Boca Raton Community Drain and Sewer Drain Cleaning Drain Clogs Electric Water Heaters Garbage Disposal Hot Water Heaters Hydro Jetting Jupiter Lake Park Lake Worth North Palm Beach Pipe Lining Pipe Relining Pipe Repair Pipe Replacement Plumber Plumbing Plumbing Installation Plumbing Leak Plumbing Maintenance Plumbing Repair Port St. Lucie Repiping Sewer Repair SEwer REplacement Slab Leak Stuart FL Tankless Water Heater Tankless Water Heaters Toilet Plumbing Toilet Repair Toilets Trenchless Pipe Lining Video Camera Pipe Inspection Water Filtration Water Heater Water Heater Installation Water Heater Maintenance Water Heater Repair Water Heaters Water Treatment Systems West Palm Beach
Update: As an aside, I also learned from my research that the best way to clean my disposal is to use citric acid. Having previously had no idea what citric acid was used for, I decided to order some from Amazon, going with the brand my sister uses: Citric Acid Powder - Ultra Fine Pure Powdered Crystals - Natural Preservative Food Grade Quality (16 oz) and gave it a whirl after 3 months of using my disposal. I let the citric acid sit with some water in the disposal for about ten minutes, and then I let it run for a solid 2 minutes. I repeated the procedure a few times and after about 30 minutes—wow, all the leftover gunk and food was flushed out of the disposal, leaving it clean with a very mild citrus scent. I feel like I’m becoming a real DIY at home kind of guy.

Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.

The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
Thank you for sharing this tutorial. My husband and I tried to fix our garbage disposal last week but we couldn’t get it to work. When we turn it on, it makes a humming noise, but nothing is blocking the blades. We might need to get a new disposal, but we’ll probably have a professional look at it before we decide. We’ll keep your tips on hand, just in case.

The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.
Some types of food remains are not easy to grind in a disposer. Do not put fibrous food items into your disposal. Help grind these items by putting in a few small bones or large ice cubes to the disposal. If the disposer won’t grind it up then turn off the disposer and remove the item with a pair of tongs. When using your disposer, make sure that the disposal is running with good water flow. Good water flow carries the waste down the drain line. Using too little water can create a clogged drain.
Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
Regarding the comments that the EZ Mount is flimsy or cheap or plastic, I have to respectfully disagree. The purpose of the lock ring is to compress the rubber gasket tight enough to make a seal so the thing doesn't leak. It doesn't need to be made from titanium or cast iron. Just because it isn't made from a rare earth metal doesn't make it inferior! It keeps the price down and works (so far) flawlessly. I did not need to tap the ears with a small hammer to get it to slide to the fully locked position - I was able to twist it into place with my bare non-Superman hands. I did not need to put dish soap on the ear slots but the directions suggest doing that if it is difficult to put into locked position.
Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.

We won’t sugar-coat it. This one is the doozy. If the leak is located at the bottom of the unit that means at least one internal seal has slipped, chipped, or flat-out deteriorated. The catch is, there are lots of these seals inside the disposal, and if one has failed it means the others are on their way. You can replace these seals with expensive, original equipment manufacturer (OEM) parts – or you can just get a new garbage disposal.
I am a researcher. I read every review - the good and the bad. I've read the Consumer Reports reviews, read the Amazon reviews, read the other, sketchier review websites like GreatGarbageDisposals.com (I made that one up but if you've done any research on the internet you get my point). I am writing this review to share what I learned about the product and about the many reviews I've read. My situation was that our 6 year old Badger froze up and simply quit on me, so a new one was in order.
Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
When rubber gaskets age, they can develop leaks. The gasket can dry up, crack, and leak when it is repeatedly exposed to long periods of disuse where no water is present in the drain pipe. Should an older garbage disposal be removed and then placed back, it will require a new rubber gasket to again achieve a watertight seal. Moreover, if a gasket is not evenly locked on all three sides, then it will develop a leak.

IMPORTANT: Whenever you are working on your garbage disposal, inserting items, and/or inserting body parts into your garbage disposal unit, it should be UNPLUGGED and the POWER TO THE GARBAGE DISPOSAL UNIT SHOULD BE OFF!  Failing to do so will put you at risk of SERIOUS INJURY.  Also, if possible avoid placing your hands directly near the blades at the disposal.  If you can, instead use a tool to wedge out items or check the blades for blockage.
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water
To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.
If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.

So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
Not every garbage disposal was created equal, and it can be difficult to discern which one is right for your home. After all, a quick internet search will show you that there are hundreds of different models to choose from. You shouldn’t automatically choose the cheapest or best rated garbage disposal. You need to find the one that is right for your unique needs.
Look for a jam. Something too tough to grind, such as a piece of glass, could be jamming the motor. Turn off the power and water, then unplug the disposal. (If it’s hardwired, turn off the breaker.) Remove the rubber baffle inside the drain-most just lift out-and shine a flashlight into the hole. Fish out the obstruction with a pair of tongs or needle-nose pliers.

Wrap plumbing tape around the threads of the sink drain where the disposal crews to the sink and the drain threads on the side of the disposal for the drain pipe. Screw the disposal back in under the sink. Screw the drain pipe back to the disposal. Tighten with the pipe wrench. Turn on the water to check for leaks and plug the disposal back in. Turn on the power switch to make sure disposal is running properly.
If the leak occurred in either of the two connections (smaller = dishwasher, larger = sewer) exiting the side of your disposal unit, it’s a pretty straightforward fix. Loosen the metal clamps on these hoses and make sure the rubber gaskets inside are not falling apart. If needed, replace these gaskets. Reattach the hoses and re-clamp the connections with new metal clamps.
Modern garbage disposal units connect to dishwasher drainpipes.  This enables dishwashers to expel leftover food scraps and residue that would otherwise accumulate in the dishwasher unit.  A common source of leaks is the area where your dishwasher and garbage disposal connect.  These leaks most often occur when the hose’s clamp is not secure enough and when the dishwasher hose cracks.  To fix this issue, simply replace the cracked section of the hose or tighten the clamp.
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?

Although the name is most famously associated with their high quality mixers, KitchenAid garbage disposals have fared well in both professional and consumer written reviews. Founded in 1919, the KitchenAid brand is the only brand in the world that produces items strictly for the kitchen. KitchenAid offers both batch feed and continuous feed garbage disposal systems for residential and commercial settings.
To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
One of the Camorra's strategies to gain social prestige is political patronage. The family clans became the preferred interlocutors of local politicians and public officials, because of their grip on the community. In turn, the family bosses used their political sway to assist and protect their clients against the local authorities. Through a mixture of brute force, political status, and social leadership, the Camorra family clans imposed themselves as middlemen between the local community and bureaucrats and politicians at the national level. They granted privileges and protection, and intervened in favour of their clients in return for their silence and connivance against local authorities and the police. With their political connections, the heads of the major Neapolitan families became power brokers in local and national political contexts, providing Neapolitan politicians with broad electoral support, and in return receiving benefits for their constituency.[26]

GE, which is an acronym for General Electric, is an international conglomerate whose headquarters are based in New York City, New York. The company operates in many different segments, ranging from home appliances to transportation. In terms of gross revenue, GE is the sixth largest company firm in the United States. GE garbage disposals have won praise for their powerful motors and overall durability.
Although the name is most famously associated with their high quality mixers, KitchenAid garbage disposals have fared well in both professional and consumer written reviews. Founded in 1919, the KitchenAid brand is the only brand in the world that produces items strictly for the kitchen. KitchenAid offers both batch feed and continuous feed garbage disposal systems for residential and commercial settings.
Flush with water. Simply flushing out the garbage disposal with water will help to remove any loose dirt or grime. Stopper the garbage disposal, add a squirt of dish soap and run the hot water until there is 2 to 4 inches (5.1 to 10.2 cm) sitting in the sink. Pull out the plug and turn on the garbage disposal, allowing the water to flush through.[2]
STEP 5 – If you are one of those rebellious types that never listens to wise instruction, then take off any rings and make sure that your hand is lubricated with liquid dish soap or cooking oil to reduce the risk of it getting stuck in the drain opening. Also, have a phone nearby. If your hand does get stuck, you can then call someone (using your other hand, presumably) to call a friend or 911 for rescue. If at all possible, don’t call a friend with a video camera phone, because they’ll probably embarass you by broadcasting your plight on YouTube.
Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
Dispose orange peels, or any citrus rinds, to freshen the disposal and keep it smelling clean, but cut them into slices first as large pieces of citrus peel, e.g. half a lime, can jam a disposal. You can also use pieces of citrus fruit that may be too old to consume, as long as they're not too spoiled to smell nice. You can freeze these pieces first, if you wish.
Energy usage is not high; typically 500–1,500 W of power is used, comparable to an electric iron, but only for a very short time, totaling approximately 3–4 kWh of electricity per household per year.[34] Daily water usage varies, but is typically 1 US gallon (3.8 l) of water per person per day,[35] comparable to an additional toilet flush.[36] One survey of these food processing units found a slight increase in household water use.[37]
×