Thanks so much! Clear, easy to follow instructions. We were able to follow step by step and got it done. I read somewhere that they used a car jack to hold the disposal when taking it off and putting it on. That was a really helpful tip for anyone else doing this. They’re fairly heavy. Also, it leaked when the gasket was just placed in the hole. We actually had to take it apart and put the gasket over the plastic pipe, then when you tighten the metal plate to connect it to the disposal, that sealed it. Anyway, thanks again. Being able to do this on our own saved us quite a bit of time and hassle.
Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services.  If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.
Many localities in the United States prohibited the use of disposers.[8] For many years, garbage disposers were illegal in New York City because of a perceived threat of damage to the city's sewer system. After a 21-month study with the NYC Department of Environmental Protection,[9] the ban was rescinded in 1997 by local law 1997/071, which amended section 24-518.1, NYC Administrative Code.[10]
Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.

Some types of food remains are not easy to grind in a disposer. Do not put fibrous food items into your disposal. Help grind these items by putting in a few small bones or large ice cubes to the disposal. If the disposer won’t grind it up then turn off the disposer and remove the item with a pair of tongs. When using your disposer, make sure that the disposal is running with good water flow. Good water flow carries the waste down the drain line. Using too little water can create a clogged drain.


Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.

Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.


I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!

Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.

We apologize in advanced for stating the obvious, but… garbage disposals absolutely do not last forever! No matter how well it’s made or how much money you spend, any appliance that is exposed to thousands of gallons of running water, dish soap, scraps of food, bones, and the rare (we hope) spoon or lime wedge that accidentally gets dropped into the drain is going to wear out in due time. A unit that’s working well should be able to handle a few scraps of veggies or apple slices in a matter of a couple of seconds. If your garbage disposal seems to take forever to accomplish a simple grinding job, makes a strange noise or emits a nasty smell, it may be time to install a new one.
Garbage disposals first appeared in households in the 1930's and 1940's. These appliances, which are installed under a kitchen sink, can make a cook's life easier by trapping and shredding food waste items, allowing it to pass through the plumbing system. Although these popular appliances make cooking and cleaning much more convenient, they do require regular maintenance to keep them running at optimal performance. When it is time to replace your garbage disposal's blades, you can save time and money by doing it yourself.
Aside from the reviews I’ve put together, I haven’t forgotten about people who are having issues with their current food waste disposer. Below you will find some links to the information pages I’ve put together that will help you fix problems you might already have. For those of you that are confused over how to unclog a waste disposal unit, take a look at this page. On the same page, we also discuss waste disposal units that won’t power up and units that are leaking.
Avoid getting grease in your drain. It is not a good idea to pour any kind of oil, grease or fat into your garbage disposal. The grease can accumulate in the disposal unit, slowing down the motor and lining the pipes, causing the drain to clog. Try to wipe off as much grease as possible from pans and roasting tins using paper towel, before rinsing.

See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.


Whether you repaired or replaced the leaking garbage disposal, test for any missed problem spots. Wipe the unit dry with a clean cloth, then unplug the sink drain (if plugged) and pour a few cups of dyed water into the drain once more. Use a flashlight to inspect the entire unit. If you don’t observe a leak, turn on the power to the disposal from your breaker box and plug in the disposal at the wall outlet.
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×