You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.
2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.

Prior to testing the garbage disposal for leaks, unplug it at the wall outlet and turn off the power from the breaker box to prevent electrical shock. Then insert a watertight sink stopper into your sink drain and wipe the unit dry with a clean cloth. In any handy container, mix a few drops of food coloring into a few cups of water, and pour the dyed water onto the sink stopper to help you locate the leak.
If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.

If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
With so many different models of garbage disposals to choose from, it can be difficult to figure out which one will best suit your needs, especially when you begin looking at all of the different features each model has to offer. Reading garbage disposal reviews will be much easier if you know what you are looking for. Here is a glossary of common features found on most modern garbage disposals:
Locate the circuit breaker that controls power to the garbage disposal, and flip it to the "off" position before continuing. Fix or replace the main seal if it is leaking. Remove both the drain pipe and the dishwasher hose, if applicable. Insert a screwdriver into the tightening ring and turn it counterclockwise. This will release the garbage disposal unit. Inspect the main seal that sits on the top of the unit. The seal is a large, soft rubber fitting that covers the top edge of the garbage disposal. If dirt, grit or food particles have fouled the main seal, wipe it down with a damp rag and reinstall the disposal unit. If the main seal is cracked, pitted or broken, it needs to be replaced. Once a new main seal has been inserted into the garbage disposal, push it up against the mounting bracket, insert a screwdriver into the tightening ring, and turn it clockwise to lock the unit into place. Reinstall the drain pipe and dishwasher hose, if applicable.
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.
InSinkErator is a brand name that is well-known for their design and manufacturing of waste disposal systems and instant hot water dispensers. John Hammes founded the company in 1927 in Racine, Wisconsin, where their headquarters remain today. Hammes is credited with designing and producing the first “in sink” waste disposal system, and the InSinkErator is a play on the word “incinerator”. Currently, InSinkErator produces and markets garbage disposal systems under the Evolution and Badger Series brand names.
GE, which is an acronym for General Electric, is an international conglomerate whose headquarters are based in New York City, New York. The company operates in many different segments, ranging from home appliances to transportation. In terms of gross revenue, GE is the sixth largest company firm in the United States. GE garbage disposals have won praise for their powerful motors and overall durability.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
Release the old disposal from the mounting ring. At the top of the unit you should see a thin metal ring with 3 separate lugs, or protruding arms. Take hold of these lugs with one hand and twist the entire ring counterclockwise about 1.5 inches (3.8 cm) to dislodge the old unit. Set it aside on a sheet of newspaper or unfolded rag to keep from making a mess.[4]
At one point, I did have a leak that I eventually determined was due to improper installation. (This was by the same "professional" plumber who reversed the hot and cold supply lines when installing a kitchen faucet. He just didn't connect the drain hose properly.) While investigating the issue, I called Waste King to inquire about possible in-home service or warranty replacement. I was blown away by their level of customer service: no waiting on hold, just an immediate connection to a person who really knew the product and was unexpectedly diligent in resolving my problem -- which, as it turns out, wasn't even their fault.
This may result in higher costs for energy needed to supply oxygen in secondary operations. However, if the waste water treatment is finely controlled, the organic carbon in the food may help to keep the bacterial decomposition running, as carbon may be deficient in that process. This increased carbon serves as an inexpensive and continuous source of carbon necessary for biologic nutrient removal.[31]
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.
Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.
Hiller Plumbing, Heating, Cooling, & Electrical provides residential and commercial service and repair throughout Tennessee, Southern Kentucky, and Northern Alabama. With our mantra, “Happy You’ll Be or the Service is Free!” we are dedicated to resolving any issue with our services.  If you have a plumbing, heating, cooling or electrical emergency, Hiller is available for 24/7, same-day service.

Locate the leak. Wipe off the disposal unit with a dry rag. Run water into the unit and turn it on. There are four places where the disposal unit may leak. At the top main seal, at the drain pipe, at the optional dishwasher inlet or along the garbage disposal body. Notice where the water is coming from. If the unit is wet at the very top, the main seal is leaking. If the area beneath the drain pipe is wet, the gasket is leaking. If the hose from the dishwasher feed drips, the hose or clamp may be faulty. If water is running out the bottom of the unit but the inlets and outlet are dry, the unit itself has developed a leak and must be replaced.
STEP 7 – You may have stubborn object stuck in the blades that is preventing the motor from rotating. This means it is time to apply a little muscle. Get your handy allen wrench out and insert the tip of the short end into the hexagon shaped hole at the bottom center of the disposal. If it doesn’t fit, find or buy one that does. They usually come in multi-pack sets with various sizes to choose form. Your disposal might have had one packaged with it. if so, find it and use that one. Once inserted, rotate it a half-turn clockwise and then a half-turn counter clockwise to see if the mechanism inside the disposal will move at all. If so, it will help to move the blades back and forth a few times to force through the obstruction. After you’re done, restore power to the disposal and turn it on. At this point, your efforts may have helped your disposal to work again. If not, try one more time.
This new one some how makes it quiet when using the disposal. I have no idea how old the other one was, it was here when we moved in. It was flimsy and would let dirty water come up. Cleaning the splash guard and the drain it went into didn't help at all. The new is firm and sits in the drain level. My daughter was putting the old one slanted some to keep it in there. After 2 1/2 years it was falling apart. I wish I'd bought one when we first moved in. This is the first garbage disposal for me but now I've learned what to expect from it. I recommend this product and will buy another if I'm still here when this one starts to get flimsy!
Using a garbage disposal is the swift and environmentally easy alternative to removing food waste from your kitchen. A garbage disposal is made to efficiently eliminate leftover food waste by grinding remains into fine particles that are easily flushed away. When shopping, look for a few key features before purchasing a garbage disposal, such as what type you will need? How much horsepower do you want? Are there any special features that you require? We also recommend to check if your waste goes to a septic tank, as this can determine the specific type you will need.
Sporting a powerful 2 800 RPM motor this Sporting a powerful 2 800 RPM motor this GE 1/2 HP Continuous-Feed Garbage Disposal makes the grinding and draining of undesirable food waste a snap making use of jam-resistant dual stainless-steel swivel impellers to help get the job done while helping to prevent disposer clogs. EZ mount installation ensures quick ...  More + Product Details Close
If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.

If the disposal is plugged in and doesn’t need to be reset, then you should check the circuit breaker. The breaker could be flipped, which would mean your disposal isn’t getting power. If that’s still not the problem, then either the outlet is dead, the circuit breaker is malfunctioning, or the disposal needs to be replaced. Check the outlet first by plugging something else into it. If the outlet works, try replacing the circuit breaker switch. If that isn’t it either, you have to replace the disposal.
If you're replacing a commercial garbage disposal, then you'll either want the Drain Strainer with Crown Adapter or the Drain Strainer XL. Both of these models have a universal Crown Adapter on top that serves as a funnel to cover the hole once the commercial garbage disposal has been removed. Note that it doesn't actually attach to the sink bowl, but you'll adjust the legs to get your unit flush underneath the bottom of the sink.
2. Can my septic tank handle the load? Septic tanks are essential in the general installation and use of garbage disposals. If your home is hooked up to a septic tank, then the municipality that you live in may require you to upgrade your septic tank system if you decide to install a garbage disposal. A local building inspector will be able to tell you if you’ll need too. Also, you must take into account that you will be required to empty your septic tank more often.
A broken garbage disposal makes tackling your to-dos an unnecessary challenge, which is why the experts at Sansone want to help. Whether your garbage disposal is leaking, clogged, humming, or completely stuck, we can repair the issue or replace your garbage disposal entirely. Contact us today with any plumbing questions or schedule an appointment that’s convenient for you by phone or on our website.
Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
×