Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
Should your disposal suddenly cease to work, check its overload protection. A red button on the bottom of the disposal trips when the disposal becomes jammed or overloaded to prevent damage and motor burnout. Unplug the disposal, push the button and remove the jam. Some high-end models can sense a jam and will automatically reverse the direction of the blades.
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:

Have you ever opened the cabinets under the sink to remove the trash or a handful of cleaning products, only to find everything soaked and soggy? Have you ever installed – or even had professionally installed – a brand new, state-of-the-art garbage disposal, only to have it flood your kitchen floor the next day? If so, you have a major plumbing: a leaking garbage disposal leaking from.

To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.

Aside from the reviews I’ve put together, I haven’t forgotten about people who are having issues with their current food waste disposer. Below you will find some links to the information pages I’ve put together that will help you fix problems you might already have. For those of you that are confused over how to unclog a waste disposal unit, take a look at this page. On the same page, we also discuss waste disposal units that won’t power up and units that are leaking.


The General Electric 1/3 Horsepower Continuous Feed is a relatively small unit. One of the most important measurements with garbage disposals is the size of the grind chamber. In this case, it’s 26.5 ounces. Power, at 1/3 horsepower, is at the lower end of the scale, but this is a light-duty machine. The owners we surveyed were very happy with the General Electric’s performance.
Built-in trash compactors fit snuggly into your kitchen cabinetry. Having a built-in compactor means you have one less appliance occupying precious floor space. A convenient toe pedal opener lifts the top open for easy hands-free opening, and a removable drawer make it easy to clean and empty the compactor. Shop for new garbage disposals and trash compactors from JCPenney today!
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
The owners of this site may earn commissions on sales resulting from any click or purchase made from a banner or link to any products or services featured on this website. Your willingness to follow those links or purchase those featured products & services will help support our site and the content we provide. Thanks in advance for supporting our site.

Michele Zagaria, a senior member of the Casalesi clan, was arrested in 2011 after eluding police for 16 years. He was found in a secret bunker in the town Casapesenna, near Naples.[44] In 2014, clan boss Mario Riccio was arrested for drug trafficking in the Naples area. Around the same time 29 suspected Camorra members were also arrested in Rome.[45]
Typically, garbage disposals usually last anywhere from 5 to 10 years. Well manufactured units may even last longer than that. If you’re really looking to save some money, you can always disconnect your unit, dissect it, seal the crack and reattach it. However, this is just a temporary fix. If you have the money, it’s best just to invest in a new unit.
A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
Since the mid-1990s, the Camorra has taken over the handling of refuse disposal in the region of Campania, with disastrous results for the environment and the health of the general population. Heavy metals, industrial waste, chemicals and household garbage are frequently mixed together, then dumped near roads and burnt to avoid detection, leading to severe soil and air pollution.
To preserve quality of life in the capital, the Moscow’s government sends streams of municipal waste into the surrounding regions. Greenpeace reports that 90 percent of Moscow’s waste goes to landfills in Moscow’s suburban region. Landfills created in the Soviet and early post-Soviet period, when there was little consumer waste, have been expanded, often with no community notification and despite being in close proximity to homes and schools. Air quality suffers as the dumps release fumes from decomposing waste.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
At the time, the Mobro 4000 incident was widely cited by environmentalists and the media as emblematic of the solid-waste disposal crisis in the United States due to a shortage of landfill space: almost 3,000 municipal landfills had closed between 1982 and 1987.[5] It triggered much national public discussion about waste disposal, and may have been a factor in increased recycling rates in the late 1980s and after.[6] It was this that caused it to be included in an episode of Penn & Teller: Bullshit! (season 2, episode 5) in which they debunk many recycling myths.
Use a wet-dry vacuum cleaner to remove any smaller shards of glass. Simply hold the opening of the hose over the top of the garbage disposal and allow the vacuum to run until you can't hear anything be sucked up anymore. If the sink isn't particularly wet, you can use a regular vacuum, covering the end of the extension tube with a nylon stocking secured with a rubber band.
Because it’s out of sight, it can be easy for some homeowners to forget they even have a garbage disposal — especially if it was installed by a  previous owner. However, an unused unit can rust and seize up, which can lead to leaks and mechanical problems. Make a habit of running your disposal for a minute or so every couple of weeks, even if you don’t actually grind anything.
Jump up ^ Specter, Michael (22 June 1992). "Only in New York: Garbage Disposers, Banned, Stir Debate". New York Times. Most major cities banned garbage disposers after World War II, driven by worries that ground food would clog sewer pipes beneath their booming neighborhoods. ... But a series of studies from universities and the not completely disinterested plumbing industry showed that the additional waste from ground food scraps would rarely harm a city sewage system.
See The Drain Strainer™ with Crown Adapter installation instructions and dimensions (or the XL installation instructions and dimensions below for taller sinks) below to see the actual dimensions for each model. The legs can adjust up to an additional 5 inches and you can add as many sets of 6 inch leg extensions as needed to achieve the proper total height.

3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.
Our Minneapolis – St. Paul plumbers assist customers with garbage disposal installation by helping them choose between a continuous feed garbage disposal or a batch feed utility. Our plumbers will discuss the best options for your home and lifestyle. Some of the benefits of our garbage disposals include anti-jamming technology, plastic or metal blades, connectors to the dishwasher, system quietness, and more.
She knew about the service call fee. The 4 On Your Side Investigation found that’s a common fee. Consumer Investigator Jodi Brooks called around to try to get an estimate from private plumbers for a garbage disposal replacement. None of the businesses we called would give an estimate over the phone. All of them wanted to look at the situation before committing to a price, and all wanted to charge a service fee to come out. Brooks found only one plumber who would come out without charging.

Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
One of the screws on the side of my Badger 5 is rusty and seems to be the source of a very minor leak. If I leave a towel in place under the side of the unit, it will saturate after a week or two. Drain, dishwasher, and sink connections are bone dry. As well as the flange connect at sink. Can I let it be or is this a major disaster waiting to happen?
Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!
If the leak occurred in either of the two connections (smaller = dishwasher, larger = sewer) exiting the side of your disposal unit, it’s a pretty straightforward fix. Loosen the metal clamps on these hoses and make sure the rubber gaskets inside are not falling apart. If needed, replace these gaskets. Reattach the hoses and re-clamp the connections with new metal clamps.
4. Is installing a garbage disposal worth the additional water expense? On average, a modern faucet runs 2.5 gallons of water per minute, or 900 gallons per year based upon the average annual household usage in the U.S. Depending on how often you use your disposerl, your home’s water usage, and water bill, will rise. This is one factor you’ll need to consider before deciding whether or not to buy a garbage disposal.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
Before your garbage disposal installation appointment, please have on hand the garbage disposal you purchased, including all screws and other pieces that came with it. If the job isn't a standard garbage disposal installation project, and requires additional parts or labor to complete the service, additional fees may apply to cover the cost of the garbage disposal parts and the garbage disposal installation work.
Some other kinds of garbage disposal units are powered by water pressure, rather than electricity. Instead of the turntable and grind ring described above, this alternative design has a water-powered unit with an oscillating piston with blades attached to chop the waste into fine pieces.[27] Because of this cutting action, they can handle fibrous waste. Water-powered units take longer than electric ones for a given amount of waste and need fairly high water pressure to function properly.[citation needed]
×