Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.

Did exactly what I expected to. We bought a house with an older disposal and the gasket/rubber that blocks things from falling down into the disposal was cut away. I replaced and is like new. It makes the disposal sound much better too. A couple things about removing disposal and installing gasket...1) use a large Allen key (short end) to stick in the eyelet to unlock the disposal. 2) the gasket fits over the mouth of the disposal and locks into place. Don't just stick the new gasket in up from the bottom hole like I did. 3) use channel locks to tighten the last bit of the disposal/sink collar by pinching the eyelet and collar screw mount. Enjoy!
Need Help?  Have a question or comment?1-888-827-4223Email UsGet Exclusive Offers & Expert TipsJOINTerms of UsePrivacy PolicyInterest Based AdsFor U.S. Residents Only © 2018 Ace Hardware. Ace Hardware and the Ace Hardware logo are registered trademarks of Ace Hardware Corporation. All rights reserved. For screen reader problems with this website, please call 1-888-827-4223 or email [email protected]
We hate to say it, but stoppages in garbage disposals are generally due to “operator error”. Either we have put too much in at one time or tried to force something through, smashing it with a spoon (there is that pesky spoon again!). Pasta, rice and salad are killers of garbage disposal drains and really need to be put down the drain in small amounts; if you put half a pot of rice in at the same time you definitely stand the change up plugging up the pipes under your sink.
So I know next to nothing about buying a garbage disposal, for the past ten years I’ve lived in huge cities and haven’t had any room (or necessity for that matter) to purchase one. Having recently bought a house, all that has changed. From dishwasher to washer to dryer to garbage disposal, I’m having to educate myself about them and purchase them with informed decision making skills. Yikes.
Reason Why It May Leak: When the rubber gasket gets old it can develop a leak. Long periods of disuse when there is no water in the drain and garbage disposal can cause the gasket to dry up and leak. If you remove an older garbage disposer for any reason and then put it back it may require a new rubber gasket to get a watertight seal again. Also, if the gasket is not locked evenly on all three sides then it will leak.

When something blocks your disposal unit’s flywheel, you will start hearing a low humming sound, and you know you’ve got a jam. Un-jamming a garbage disposal is something that depends on the specific unit you own. Every single one has a function to shut off when they are stuck to the point of stalling the motor. This is so the motor doesn’t burn out. However, they are also designed so that anyone (and we mean anyone!) can remove whatever it is that is blocking your unit. Underneath every unit is a small slot, and pretty much all of them come with a tiny little wrench to match it. These are most commonly called hex-head wrenches. Yes, that little tool that you probably have no idea where it could possibly be has a very specific and important purpose. Mind blown, right?


Two Aberdeen restaurateurs, Ciro Schiattarella and Michele Siciliano, were extradited to Italy for their part in the "Aberdeen Camorra". A fourth Scottish associate made history by becoming the first foreign member of the Camorra and is currently serving a jail sentence in the UK. It has been reported that he also receives a monthly salary, legal assistance and protection.[55]
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
In the event that you do not have a grounded outlet to power the garbage disposal, you will need to install one. Adding a grounded outlet may cost as little as $5 when existing electrical wiring is placed a short distance away, plus an additional $75 for the electrician's labor. If a new grounded outlet needs to be added and electrical wiring does not yet exist, it will likely cost around $90, depending on labor and parts. If your project requires the addition of a new switch and wire, plan to spend an average of $5 to $10 on materials, plus about 30 minutes of labor at an average cost of $75 an hour.
You should first find out whether only the disposal is broken, or if the power has gone out completely in the areas near your kitchen sink. Try resetting the circuit breaker that leads to the kitchen, or replacing a fuse if you have an older electrical box. If the garbage disposal makes no noises at all when you flip the switch, you might also want to check under the sink to see that it’s plugged in.

Garbage Disposal Install

×