But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.
STEP 3 – Clear out the disposal to remove any bits of hard foods, bone shards or other fibrous gunk that may be preventing the grinding blades from rotating and pulverizing your discarded food. Use a tool (a pliers, wooden spoon, etc.) to do this. Putting your hand in situation where whirling blades of destruction are nearby is never a good idea. (That is what I’ve heard anyway.)
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

3. Is my plumbing capable of handling the task? If your current plumbing frequently clogs or backs up, then you should NOT install a new garbage disposer. The additional waste that a garbage disposal creates will only increase the chances of one or both happening. Before installing a waste disposer, you’ll need to have the source of the problem identified and fixed.


Knowing the difference between what can go down the disposal and what should go into the trash can save you an emergency call to the plumber. This is especially pertinent during the holidays when the kitchen is filled with people and the sink with dirty dishes. Practice these three everyday maintenance tips to help you maximize the lifespan of your garbage disposal.
Knowing the difference between what can go down the disposal and what should go into the trash can save you an emergency call to the plumber. This is especially pertinent during the holidays when the kitchen is filled with people and the sink with dirty dishes. Practice these three everyday maintenance tips to help you maximize the lifespan of your garbage disposal.
With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes ... full review

Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.


Set the garbage disposal down where you can work on and see the rubber gasket. Peel off the old gasket and put the new gasket in the same place making sure that it pops into the lip and sits flat. Now you are ready to set the garbage disposer back in place. Use your knee or a helper to lift the disposal into place while looking down at it from above the sink to verify that the gasket sits flat before locking it back into place. Then look underneath the sink to make sure that all three mounting grooves are locked in. Reconnect the drains and plug the cord back in to test it for leaks.
The large-capacity disposer chamber boasted by this GE The large-capacity disposer chamber boasted by this GE 1/3 HP Continuous-Feed Garbage Disposal features a cold-rolled carbon steel armature shaft and dishwasher drain connector. It also has a stainless-steel sink flange ensuring durability and providing ample space for waste disposal. The disposer harnesses the power of jam-resistant dual stainless-steel swivel ...  More + Product Details Close

To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.


I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
To replace a rubber gasket, your first step will be to unplug the cord to the garbage disposal and then disconnect the drain. If you have a dishwasher installed in your kitchen, the dishwasher drain hose will need to be disconnected from the disposer. With the cord and appropriate drain lines removed, you can now grasp the sides of the mounting nut and twist it in a counter clockwise motion, which unlocks the garbage disposal. The waste disposer should then drop right down.
Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

Garbage Disposal Installation

×