Lift the sink flange from the top of the sink. Use a plastic putty knife to scrape off the old plumber’s putty around the top of the flange, then wipe off any putty residue with a damp rag. Grab a palmful of plumber’s putty from the container and roll it into an eighth-inch to quarter-inch-wide “rope” with a length roughly equal to the circumference of the flange. Wrap the rope of putty around the top of the flange like a collar, then insert the flange into the sink drain opening until snug. Re-install the mounting assembly and mounting ring (taking care to securely tighten the mounting bolts on the mounting assembly), then re-attach the garbage disposal, drain pipe, and dishwasher hose in the reverse order you detached them.
Modern food waste disposers are often connected to your dishwasher’s drain pipe. This connection enables your dishwasher to rid itself of any leftover food scraps or residue that it might accumulate while washing your dishes. Where the dishwasher hose and the garbage disposal connect is a common source for leaks. The leaks most often occur when hose’s clamp is not secure enough. Leaks also develop when the dishwasher hose cracks. In order to fix this type of leak, you should either replace the cracked section of hose or tighten the clamp down.
Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
One result is larger amounts of solid residue from the waste-water treatment process. According to a study at the East Bay Municipal Utility District’s wastewater treatment plant funded by the EPA, food waste produces three times the biogas as compared to municipal sewage sludge. The value of the biogas produced from anaerobic digestion of food waste appears to exceed the cost of processing the food waste and disposing of the residual biosolids (based on a LAX Airport proposal to divert 8,000 tons/year of bulk food waste).
Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
InSinkErator is a brand name that is well-known for their design and manufacturing of waste disposal systems and instant hot water dispensers. John Hammes founded the company in 1927 in Racine, Wisconsin, where their headquarters remain today. Hammes is credited with designing and producing the first “in sink” waste disposal system, and the InSinkErator is a play on the word “incinerator”. Currently, InSinkErator produces and markets garbage disposal systems under the Evolution and Badger Series brand names.
A foul or foreign odor emanating from the garbage disposal that won’t go away no matter how thoroughly you have rinsed it, may also be a sign that it’s time to replace it. As the components in the grinding chamber wear out and the blades get duller and duller, food can easily get trapped inside and start to decompose. You may never have noticed the smell or have chosen to adapt and wait it out, but it may be a sign of a deeper problem. Visiting family members and dinner guests probably wouldn’t appreciate it very much, either.
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
Most garbage disposals are sealed using plumber’s putty. You’ll need to detach the garbage disposal, clean off the old putty and reseal. Other types of disposals use only a flange that is tightened and compressed with screws. This may need to be replaced. Either way, this can be a big job if you don’t know what you’re doing (requires removing and replacing drain pipes, as well).
There are many potential causes for a leaky garbage disposal. Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable. Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.
Connect the connector pipe to the elbow and the adjacent sink. Use the connector pipe to connect the elbow piece to the T-fitting on the adjacent sink. The connector piece might need to be cut down to the correct length depending on your sink. Use the nuts and washers provided with your pipes to secure the pieces together using the tongue-and-groove pliers.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
Turn off power to the disposal before attempting to clear the jam. Use the wrench to turn the blades in both directions to loosen the obstruction. Try to run the disposal again. If you don’t hear the motor at all, it’s possible that your disposal’s overload protector has been tripped. If your disposal has this feature, it can be reset by pushing a button somewhere on the outside of the unit.
In the United States, almost all garbage disposals on the market are manufactured by a handful of companies; although, many are branded under different names. For example, out of the top ten highest rated models on the market, InSinkErator makes eight of them. Whirlpool and WasteKing are the other two most well-known brands in the U.S. There are a wide range of models to choose from, ranging from basic $50.00 models to models equipped with all of the latest bells and whistles that can cost as much as $600.00. In most cases, you get what you pay for in terms of quality. Here is a brief overview of the top brands in the U.S.
Today, we are living in the modern world of light-speed schedules and convenience. Garbage disposals have become a time-saving, convenience. Though garbage disposals make disposing of foods a simple task, they often go overlooked or under appreciated. Nevertheless, when something goes wrong, we cannot fail to notice the foul smell coming from our garbage disposal units.
Loosen the nut securing the rest of the assembly. Just below the sink flange where the drain empties into the garbage disposal you’ll see a circular plastic piece similar in appearance to the mounting ring. Insert the tip of a screwdriver into one of the lugs on this piece and rotate it in a counterclockwise direction. Pull the nut away and set it aside.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.