Manufacturers’ warranties for garbage disposals range from one year through the lifetime of the unit. One of the best warranties in the industry is the one offered by WasteKing on all of their garbage disposals. Should your disposal system fail due to material defect or mechanical effort during the purchaser’s lifetime, WasteKing will replace the unit for free. This is compliance to the policies provided for by their lifetime warranty.
Has a dual outlet to connect two appliances instead of one. You can connect your household waste disposal and a hot water dispenser (if you want). The power switches between the 2 outlets. When you press the switch to run the disposal, the water dispenser will be turn off. Once you press again to power off the disposer, the water dispenser will be turn on. Only one outlet is active at all times.

Badger food waste disposers are a reliable and Badger food waste disposers are a reliable and functional choice when affordability is the prime concern. Badger 5XP features a 3/4 horsepower heavy-duty quiet Dura-Drive induction motor rugged galvanized steel construction for disposer durability and a space-saving compact design. To top it off Badger 5XP offers a 3-year We Come ...  More + Product Details Close
The InSinkErator Badger 5 1/2 HP Continuous Feed Garbage Disposal features a quick-mounting system that allows for easy installation or replacement of most disposers. This garbage disposal also features a 1/2 HP motor that rapidly grinds food waste for easy rinsing down the drain. The garbage Disposal also features galvanized steel construction for durability.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.

Flush with water. Simply flushing out the garbage disposal with water will help to remove any loose dirt or grime. Stopper the garbage disposal, add a squirt of dish soap and run the hot water until there is 2 to 4 inches (5.1 to 10.2 cm) sitting in the sink. Pull out the plug and turn on the garbage disposal, allowing the water to flush through.[2]


Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.

The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
If your garbage disposal has become clogged, you’re likely to hear a muted humming noise when you flip the switch. This is an indication that your garbage disposal is getting power, but the blades aren’t able to turn. Very often, this happens when something hard and non-crushable has become caught in the blades at the bottom of the unit. To solve this problem, do the following:
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.

In 1983, Italian law enforcement estimated that there were only about a dozen Camorra clans. By 1987, the number had risen to 26, and in the following year, a report from the Naples flying squad reported their number as 32. Currently it is estimated there are about 111 Camorra clans and over 6,700 members in Naples and the immediate surroundings.[29] Roberto Saviano, an investigative journalist and author of Gomorra, an exposé of the activities of the Camorra, says that this sprawling network of Camorra clans now dwarfs the Sicilian Mafia, the 'Ndrangheta and southern Italy's other organised gangs, in numbers, in economic power and in ruthless violence.[30]
I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
Read the directions for your model before attempting a home repair. Most disposals have an electrical reset button, and a manual hex key for un-jamming. If the disposal stops working, its internal circuit breaker may have shut it off. Turn the switch definitely off, and try to pull out the hard object that may have jammed it. Then use the right-sized hex key to manually turn the rotor parts (usually directly under the unit in the center). If it turns, then push the reset button. It usually clicks in. Then, turn on the water and try the power, again.
Connect the connector pipe to the elbow and the adjacent sink. Use the connector pipe to connect the elbow piece to the T-fitting on the adjacent sink. The connector piece might need to be cut down to the correct length depending on your sink. Use the nuts and washers provided with your pipes to secure the pieces together using the tongue-and-groove pliers.[1]
Personally I'd recommend if you have a disposal have it removed. Most people don't realize, there is very little you are supposed to put in them. Whereas, they are the primary reason for your kitchen sink drain getting clogged. Just use the trash, it could save you an expensive Drain cleaning bill. Here's a tip for y'all who do have them. After use let warm water run while it's still running for 3 to 4 minutes, that will help push everything to the bigger main drain .
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
Designed to effectively grind your daily food scraps, the compact InSinkErator Badger 5 garbage disposal is the reliable choice when affordability and space are prime considerations. Featuring a powerful, 1/2 horsepower, Dura-Drive induction motor, there are no wearable parts to deliver consistent, maintenance-free performance year after year. It features a patented Quick Lock sink mount that allows for easy installation and disposal replacement. The functional Badger 5 includes an exclusive "We Come to You" 2-Year In-Home Limited Warranty.
If the disposal is hit hard enough, it can actually move and shift so that it no longer sits right. The pipes can be moved; the seals can be pressed in an awkward position; or the retaining bolts can loosen. Make sure nothing has been knocked out of place. Then, check to see where the water is coming from and tighten up the bolts. If this does not fix the leak, then you will need to replace the putty or the sealing ring.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.

However, if your garbage disposal is fairly new, having the reset button repaired is a better choice, especially if your unit is still under warranty. If your unit is under warranty, the company will probably send out a repair man to fix the job. On the other hand, if your unit isn’t under warranty, it’s best to have a skilled technician complete the job unless you have experience doing this.
This Frigidaire 1/2 HP Garbage Disposal is designed This Frigidaire 1/2 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
×