InSinkErator garbage disposals provide a convenient and environmentally-conscious alternative to sending leftovers to landfills. Capable wastewater treatment plants can even recycle food scraps into energy and fertilizer. Plus, using garbage disposals can significantly reduce the amount of trash sent to landfills and reduce greenhouse gas emissions.
Garbage disposals aren’t exactly quiet, but the device shouldn’t make a terrible screeching noise either. If your appliance is guilty of shrill sounds, there are a few potential causes. The grates could have shifted causing the device to move incorrectly, or the motor could be worn out. In either case, this usually occurs when a garbage disposal is at the end of its life, so replacement is a good option.
Keep anything too hard out of the disposal. The shredder will dull and become less efficient. Small hard objects can also get stuck and jam the rotating parts. Each garbage disposal has its own capacity for hard objects. The more expensive models of the same brand tend to have higher hardness capacities. The instruction manual usually specifies a list of objects to avoid. You can also gain experience with your own garbage disposal. Strong vegetable fibres can jam some garbage disposals, as well. If something may be harder than what the disposal handles, just put it in your trash can or think about setting up a worm composting bin. Some items to avoid are:

The metal sink flange that sits directly inside the sink drain is typically sealed around the top with plumber’s putty (a clay-like sealant) and then secured from under the sink with bolts. If the plumber’s putty deteriorates, or the bolts loosen, the flange can no longer form a watertight seal between the sink drain and the disposal—which could cause a leak at the top of the unit.


Save yourself a lot of hassle and go with the same brand & model. By doing so you'll avoid having to remount and mess with the drain & sink connections. Save the old power cord so you don't have to buy a new one. You'll need to do some very minimal wiring work to pull the wires from the terminals in the old disposal and attach them to the disposal. Make sure to attach the green grounding wire to avoid getting shocked when you switch on the disposal!

If some bad odors are coming from your disposal, it can mean that it is not chopping up the food finely and there are drainage issues. Try putting lemons peels (not wedges, y’all) through it first and see if that removes the odor. If that doesn’t help or if the smell returns frequently, that may be telling you that that the disposal isn’t swallowing and chopping up your leftovers correctly.
Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.
Attach the pipes. You will attach a 90-degree disposal drainpipe to the disposal and the tailpiece to the other sink drain. There should be p-traps on both the disposal and the tailpiece from the other sink and they should be level to one another. Use straight pipes and a T-fitting to connect both drains into one line and route the drainpipes into the main drain.

Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)

Proper use of a garbage disposal can stave off future leaks. So remember to grind only soft foods; hard items such as bones, apple cores, or raw potatoes can dislodge or damage the internal seals. Run cold water through the sink drain before and after food disposal to keep solid fats from congealing into gunk (which can deteriorate the sink flange and cause leaks). Finally, inspect your disposal for leaks—at least twice a year using the dyed-water test—to catch and repair minor leaks before they lead to water-damaged sink cabinets or kitchen floors.
Our Minneapolis – St. Paul plumbers assist customers with garbage disposal installation by helping them choose between a continuous feed garbage disposal or a batch feed utility. Our plumbers will discuss the best options for your home and lifestyle. Some of the benefits of our garbage disposals include anti-jamming technology, plastic or metal blades, connectors to the dishwasher, system quietness, and more.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).

If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.
But to dislodge whatever’s causing it to be in a bind you can use the hex wrench that came with the garbage disposal. I know most people lose them, that’s okay. Grab your set of Allen wrenches, get the right size, insert it into the recess hole right in the bottom of the disposal, and turn it left and right until you dislodge whatever caused it to get into a bind.

Even though a leaking garbage disposal is a fairly simple fix, there can be a few factors that can complicate the process somewhat. For example, there are a few different places within the connection system that may spring a leak, so often the hardest part of fixing a leaking garbage disposal is trying to determine where the leak is coming from.Aside from the obvious connections, possible areas for leaks include water inlets and outlets as well as rings and seals.
Plug the disposal and fill up the sink with hot water and detergent. Unplug and run the disposal. The spinning disk forces the water down the drain like a pump. This should clear the disposal and the drain line. If not, you'll need to inspect the plumbing. Old pipes made of iron clog easily due to internal corrosion and should be replaced with copper.
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”
If your garbage disposal just won’t turn at all, then it’s very likely that the disposal has lost power. Your unit may have blown a circuit, or it could be unplugged. First, check the plug for your garbage disposal to ensure that it’s secure. Next, locate the reset button on the underside of the unit, and push it. If neither of these things fixes the problem, look inside your electrical panel for signs of a tripped circuit.

Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
Waste King 9930: 1/2 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Durable, all-metal mounting assembly. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
Located in Benton Harbor, Michigan, the American based Whirlpool Corporation is an international manufacturer and marketer of home appliances. Whirlpool markets many different brands, including KitchenAid, Maytag, Jenn-Air, and Amana. Their line of in sink disposers offer an affordable entry level option for homeowners who want to install a garbage disposal in their home.
Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.

Wrap plumbing tape around the threads of the sink drain where the disposal crews to the sink and the drain threads on the side of the disposal for the drain pipe. Screw the disposal back in under the sink. Screw the drain pipe back to the disposal. Tighten with the pipe wrench. Turn on the water to check for leaks and plug the disposal back in. Turn on the power switch to make sure disposal is running properly.

Disposers range between $45 and $250, and most hold up fairly well under normal use. It's common for a $50, 1/3-hp disposer with a 1-year warranty to last 10 to 12 years. So what does more money buy? Increased longevity, longer warranties, more power and less aggravation. The better units have stainless steel components, auto-reversing starts and bigger motors. Units that reverse direction with each start greatly reduce stoppages, while larger motors can chew through larger and more varied food loads.


As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.
Kitchen waste appliances are necessary for every home. You are able to quickly get rid of all types of waste with ease. First thing’s first, which type is better for your home – a trash compactor or garbage disposal? Many people think the terms are interchangeable, but they function in two different capacities. A disposal is great for getting rid softer food wastes, such as mashed potatoes, veggies, noodles, and rice. Harder to grind foods, such as chicken bones, vegetable peels and egg shells, are best suited for a stainless steel trash compactor. You can even place plastic and glass bottles in the compactor.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.

3/4th Horsepower – This garbage disposal model is ideal for households of 4-5 people. It is the model that you will most commonly find in modern day homes. These models are often equipped with more sound dampening features, which reduce the level of noise the unit produces when compared to its lower end cousins. Again, it is recommended that you look for a model with stainless steel grinding components.

Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]


If the garbage disposal won't turn on but the motor makes a humming sound when you flip the switch, it indicates that the inner flywheel is jammed. Usually, this causes the appliance's reset button to pop or the circuit breaker to trip very quickly. This is not a situation you want to continue for very long, as it can burn out the disposer's motor unless the reset button or circuit breaker shuts things off. 

Español: limpiar un triturador de basura, Português: Limpar um Triturador de Alimentos, Italiano: Pulire un Tritarifiuti da Lavandino, Deutsch: Den Küchenabfallzerkleinerer reinigen, Français: nettoyer votre broyeur d'évier, 中文: 清洁垃圾处理器, Русский: почистить утилизатор отходов, Bahasa Indonesia: Membersihkan Saluran Pembuangan Sampah, Nederlands: Je afvalvermaler schoonmaken, العربية: تنظيف مصرف النفايات

Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.


STEP 1 – Many garbage disposals (a.k.a electric pigs) have a reset button located at the bottom of the unit that behaves likes a breaker switch or the reset button found on some electrical outlets. You may have to feel around for it if you can’t see it. While the disposal is off, press this button and then try to activate the disposal. If this works, skip the remaining steps and get back to doing your dishes! You solved the problem!

Despite the overwhelming magnitude of the problem, law enforcement officials continue their pursuit. The Italian police are coordinating their efforts with Europol at the European level as well as Interpol to conduct special operations against the Camorra. The Carabinieri and the Financial Police (Guardia di Finanza) are also fighting criminal activities related to tax evasion, border controls, and money laundering. Prefect Gennaro Monaco, Deputy Chief of Police and Chief of the Section of Criminal Police cites "impressive results" against the Camorra in recent years, yet the Camorra continues to grow in power.[42]
Our most affordable large-capacity model ready to tackle Our most affordable large-capacity model ready to tackle meals of up to 750 persons with its powerful 3 HP motor. Like all InSinkErator food service disposers it delivers superior performance quiet operation maximum energy efficiency and long service life. Designed for continuous operation in locations such as large banquet facilities ...  More + Product Details Close

Trim the discharge tube as needed. If you’ve upgraded to a larger disposal or one of a different model, there’s a good chance that the discharge tube won’t be the right length to connect to the ground plumbing valve. Fortunately, this is a simple fix—mark the spot on the tube where it should line up with the drain pipe, then cut it to size with a hacksaw. It should be a perfect fit.[19]
If not enough wire is exposed, you may need to strip some more of the wire’s insulation off the ends using a wire stripper. Connect the black wires to each other, then the white wires to each other, twisting the ends together in a clockwise direction with a pair of pliers. After twisting the ends together, cover the twisted wire with a wire nut, twisting clockwise until it is snug. Remember, “Righty Tighty, Lefty loosey.”
I'm not what you'd call a handyman, although I've been working to get better at that. I will now at least try a home project before passing on it. So, when our 15-year garbage disposal died I had another opportunity. I determined our old unit to be a Badger 5 1/2 HP (this exact item). I didn't have time to wait for the item to arrive from Amazon so I went to Home Depot and coughed up an extra $20 for the Badger 500 - Home Depot's branded version of this item. They are identical except for the name & sticker.

Hold a noncontact voltage detector against the wall switch with the switch in the on position. The presence of electricity at the switch causes the detector to beep and flash. Leave the switch in the on position and hold the detector against the outlet beneath the sink. If the detector does not sense the presence of electricity at the outlet, the switch may have failed and electricity can no longer reach the disposal motor. Have the wall switch replaced.


This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close

×