Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]

If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).
A high-torque, insulated electric motor, usually rated at 250–750 W (1⁄3–1 hp)[22] for a domestic unit, spins a circular turntable mounted horizontally above it. Induction motors rotate at 1,400–1,800 rpm and have a range of starting torques, depending on the method of starting used. The added weight and size of induction motors may be of concern, depending on the available installation space and construction of the sink bowl. Universal motors, also known as series-wound motors, rotate at higher speeds, have high starting torque, and are usually lighter, but are noisier than induction motors, partially due to the higher speeds and partially because the commutator brushes rub on the slotted commutator.[23][24] Inside the grinding chamber there is a rotating metal turntable onto which the food waste drops. Two swiveling metal impellers mounted on top of the plate near the edge then fling the food waste against the grind ring repeatedly. Sharp cutting edges in the grind ring break down the waste until it is small enough to pass through openings in the ring, whereupon it is flushed down the drain.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.

Some higher-end units have an automatic reversing jam clearing feature. By using a slightly more-complicated centrifugal starting switch, the split-phase motor rotates in the opposite direction from the previous run each time it is started. This can clear minor jams, but is claimed to be unnecessary by some manufacturers: Since the early sixties, many disposal units have utilized swivel impellers which make reversing unnecessary.[26]
If the plumber’s putty has failed, you might be able to stop the leak by replacing the putty.  To do so without removing your garbage disposal, loosen the retaining bolts until a gap forms, force the new putty between the pipe and flange, and retighten the bolts to secure the putty into place.  If this does not work, then remove your disposal unit and reseal the flange.  To do this:
Run cold water while the disposal is on. Keep disposer and water running for 30 to 60 seconds AFTER the waste matter has cleared your drain. The waste still has a distance to go. Cold water keeps the motor, bearings and shredder assembly from overheating. It also lets the waste go down easier because the water is pushing it down. Don't use hot water, because it can melt fat and allow it to re-solidify as a blockage further down in the drain.

To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.

To remove the gasket and replace it you will first have to disconnect the drain and unplug the cord to the garbage disposal. Also, if you have a dishwasher you will have to remove the dishwasher drain hose from the garbage disposal. With the drains and cord removed you can now take hold of the sides of the mounting nut and twist it counter clockwise to unlock the garbage disposal. The disposal should drop straight down.
The Camorra has proven to be an extremely difficult organization to fight within Italy. At the first mass trial against the Camorra in 1911–12, Captain Carlo Fabroni of the Carabinieri gave testimony on how complicated it was to successfully prosecute the Camorra: "The Camorrist has no political ideals. He exploits the elections and the elected for gain. The leaders distribute bands throughout the town, and they have recoursed to violence to obtain the vote of the electors for the candidates whom they have determined to support. Those who refuse to vote as instructed are beaten, slashed with knives, or kidnapped. All this is done with assurance of impunity, as the Camorrists will have the protection of successful politicians, who realize that they cannot be chosen to office without paying toll to the Camorra."[36]
3/4th Horsepower – This garbage disposal model is ideal for households of 4-5 people. It is the model that you will most commonly find in modern day homes. These models are often equipped with more sound dampening features, which reduce the level of noise the unit produces when compared to its lower end cousins. Again, it is recommended that you look for a model with stainless steel grinding components.

Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
First, – and this may seem obvious, but- make sure the disposal is plugged in. With that said, let’s get to the bottom of this. If it is plugged in then press the reset button, which can be found on the bottom of the unit and is usually red. You should see the button popped out- press it. If that doesn’t work, make sure the circuit breaker hasn’t tripped and turned off in the electrical service panel. If the breaker has not tripped and the reset button is not popped out, then it could either be a damaged switch or a damaged unit all together. If the disposal will still not turn on and makes no noise, the garbage disposal is beyond repair and needs to be replaced. Unless you have a solid background as an electrician, we really don’t recommend you try replacing the switch yourself. Give us a call at John Moore Services first and make sure you take the proper, safe steps.
Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.
Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.
If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.

Determine whether there's an Allen-wrench port at the bottom of the disposal, which is located under the sink. If there is, insert an Allen-wrench into the port and turn it back and forth to move the masher plate and dislodge the glass. If you can't find an Allen-wrench port, insert the handle of a broom or a hammer into the top of the garbage disposal and wiggle it around to try to dislodge the glass.
To fix this problem, turn off the disposal, fill the sink halfway full with soapy water, and use a cup plunger to plunge the kitchen sink for 30 seconds to one minute. If you cleared the clog, the water in the sink should start draining at a normal pace again. If you’re still have issues, you might have to remove the P-trap under the sink to get at the clog with a snake.

To be prepared, measure the distance from the outlet to the top of each disposal before you remove the old unit. If the new unit’s outlet is lower, you must also lower the tee that the discharge pipe connects to. Loosen the two nuts that connect the tee to the tailpiece above and the trap below. Try lowering the tee to see if the tailpiece is long enough. If it’s not, you’ll have to replace it with one that’s slightly longer.
We have an annoying habit of letting the sink fill with dishes (I know *I* surely don't contribute to such, so it must be everyone else). Occasionally, the disposal backs up if you don't run it, so the sink begins to fill with water. When that happens, you can't see if there is any flatware in the bottom of the sink to get sucked down and chewed up. By sitting down in the drain, the Disposal Genie keeps that from happening, while letting you still run most of your scraps into the disposal.
If not, unplug the disposal from its electrical outlet and test the outlet with another appliance, such as a hair dryer. If it is hardwired to an electrical box or it doesn’t work, go to the circuit breaker panel and reset the circuit breaker that serves the disposal (often the same circuit used by the dishwasher) by turning it all of the way off and then back on.
Leaks can also happen at the dishwasher connection and the discharge drainpipe. The dishwasher connection may simply need the clamp tightened or need a replacement hose. For the drainpipe, tightening the bolts may help, but if that doesn’t work, the gasket may need to be replaced. No matter the situation, it is best to give us at John Moore a call rather than trying to replace these things yourself to make sure it is done correctly and to make sure the problem doesn’t get even worse.

The government has made an effort to combat the Camorra's criminal activities in Campania. The solution ultimately lies in Italy's ability to offer values, education and work opportunities to the next generation. However, the government has been hard pressed to find funds for promoting long term reforms that are needed to improve the local economic outlook and create jobs.[40] Instead, it has had to rely on limited law enforcement activity in an environment which has a long history of criminal tolerance and acceptance, and is governed by a code of silence or omertà that persists to this day.[41]
Most modern kitchen sink drains are this dimension--both on the garbage disposal side and the "rinse" side. These are well made items that work very effectively. Unlike most kitchen sink stoppers that rest on top of the drain opening and extend upwards into the sink when you're doing dishes, these fit down into the large opening and seal the smaller opening above the garbage disposal or "rinse" sink drain strainer. In other words they seal the drain without extending upwards into the sink full of water.
Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.
Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.

Garbage Disposal Installation

×