There are many potential causes for a leaky garbage disposal.  Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable.  Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.

If there is no item stuck in the blades of the disposal obtain the Allen wrench that should be attached to your disposal or that came with it. There is a breaker socket located on the bottom of most disposal brands. Place the Allen wrench in the breaker socket and turn it back and forth. By doing this you may be able to unlock the source of the problem. Just be certain that the disposal is not turned on when doing this.
• Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. Never use your hand. To clean a garbage disposal of built-up sludge and debris, fill it with ice cubes and a cup of rock salt and then run it for about five seconds. If your garbage disposal smells bad, you can deodorize it by running warm water down it while you grind a quartered lemon.
Replacing a failed garbage disposer can seem daunting. There's the usual trepidation about electricity and water, the unfamiliar sink connection and enough drain fittings to make leaks a real possibility. Then there are the hassles of comparison shopping and the suspicion that the job could run into real money. And finally, failed disposers don't often leak, at least not in the beginning, so it's easy to put things off.

While inspecting your unit, if you see leaking, you will need to equip yourself with a screwdriver and tighten up the clamp that’s holding the garbage disposal to the dishwasher. The smaller drain line is attached by screws. Tighten up these screws and if the gasket is worn, replace this too (Careful not to overtighten). You should be able to purchase gaskets at your local home improvement store for a fairly inexpensive price.
If you are connecting the disposal to a dishwasher, it may be connected through an air gap. Use a hose clamp to attach the drain hose to the dishwasher inlet. Now that everything is installed and in position, lock the disposal to the sink mounting assembly using the wrenchette that came with the unit. For Evolution models, insert the Quiet Collar® Sink Baffle into the sink opening by pressing it into the sink until it snaps into place. (See Fig 7d)
I believe if you always run your water first, turn on disposer, then discard food waste down disposer, you will get more longevity from your disposer and less likely have drain stoppage problems. It's also a good practice to run plenty of water (maybe even cleanser) after using the disposer to rinse out the small chamber between the blades and drain pipe. I've found that some disposer stoppages are caused by this chamber being clogged which also causes it to rust and deteriorate prematurely.
One last thought - Beef bones? I see that Consumer Reports tests these things by measuring the fineness of the grind using beef bones. Do people really put beef bones down a garbage disposal on purpose? You might think I'm babying mine, or maybe that's why I didn't have excessive vibration when I use it, but I'll put the beef bones in the trash and grind up the rest of the stuff with this and be just fine for many years to come, I hope!
Flip the disposer over and unscrew the electrical cover plate on the bottom of the disposer by removing the cover plate screw. Again, be sure the power to the unit has been turned off at the electrical supply panel. Then disconnect the electrical cable connector. Pull out the wires and remove the wire nuts. Also unscrew the ground wire from the green ground screw. Be sure to save the electrical cable connector so you can use it again.

You’ll need to measure the new discharge tube to make sure it fits into the existing drain assembly. In our installation, the garbage disposer doesn’t use the discharge tube, but connects directly to the drain. If this isn’t a replacement project, you’ll need to tie in a drain assembly to the existing sink drain, which might take reconfiguring the drain. Be sure to reach the manufacturer’s instructions, and check out our Frequently Asked Questions section on this site for more information on how to do this, or visit your local independent home improvement retailer for the products and advice you’ll need for this step of the project.


The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Back Flow Prevention Bathroom Remodel Blog Call the Plumber Community Involvement Community Plumber Drain cleaning Flooding Frozen Pipes Garbage Disposal Gas Leak Green Plumber Hot Water Solutions Leaks Licensed Plumber Plumbing Plumbing Maintenance Plumbing Review Prince Of Plumbing Septic System Sewer Leak Shower Replacement Soft Water Sump Pump Tankless Water Heater Toilets Uncategorized Water Heaters Indiana Water Leaks water lines water softener Well water

Start by turning off and unplugging the garbage disposal. Next, you’ll need the wrench that came with your disposal. If you don’t have it, you can buy a replacement in a hardware store that sells your disposal brand. Find the hex-shaped opening at the bottom of the disposal unit. Turn the wrench clockwise to dislodge whatever’s blocking the flywheel. When the object dislodges, you’ll feel the flywheel start to turn easily. Reset the disposal and run cold water while quickly turning it on and off repeatedly.
Russian activists have come under increasing pressure since Putin returned to office in 2012. Protests have been relatively scarce after the 2011-2012 Bolotnaya demonstrations in response to election fraud. Long-standing nongovernmental groups working on environmental and human rights issues, which relied in part on funding from abroad, have been labeled “foreign agents” by Russia’s Ministry of Justice.
Garbage protests in Volokolamsk and elsewhere have exposed weaknesses in Russia’s system of political authority, often described as a “power vertical” in which government officials answer not to their constituents, but to their political superiors and ultimately to President Putin. Facing unresponsive or incompetent officials, citizens turn to Putin as the only one who can solve their problems.
After you install the new sink flange, you don’t want it shifting around when you’re assembling the parts underneath. Movement of the flange could break the seal between the flange and the sink, inviting a leak. Your best bet is to ask a helper to press down on the sink flange, or if you’re working alone, find something to weigh it down, such as the old disposal. Place an old towel under the weight so you don’t scratch the sink. If the bottom of your sink is quite concave, the old disposal might not contact the flange. In that case, place a can on the flange, then weigh down the can.
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in 2004. She attended Tarrant County College and studied English composition.

Garbage Disposal Repair

×