First, is it loud or quiet? It really depends on which review you read, apparently. I believe it depends on more than that, such as what kind of sink is it being installed under - a stainless steel or a porcelain coated cast iron sink? One is very thin and flexible and will not block out as much noise or damp vibrations as effectively as a heavy cast iron sink. I have found the overall noise level to be a lot like the Badger 5 that I replaced. My wife thinks it sounds a bit different but neither louder nor quieter. It also depends on whether this is your first disposer (it is certainly louder than not having one) or a replacement. Bottom line, it's typically run for a few seconds, with the water running too, as you are cleaning up after meal (not in the middle of the night when everyone's trying to sleep) and it's no louder or quieter than the rest. I wouldn't let that be a deciding factor unless you have different criteria. If so, you can pay twice as much for that other "Elite" one by another manufacturer that is CR-rated as the quietest one. In my case I couldn't justify the added cost.
I found a vertical crack, about 1 inch long, along the upper part of the disposal housing. The unit, an insinkerator badger 9, is from 2010. When water goes through the unit, a small amount will drip. The amount of water is actually quite limited, even when using lots of water to wash dishes. The unit is obviously old, but seems to work fine otherwise. What are your recommendations? Replace? or just catch the dripping water (1 table spoon per day).
Garbage disposers address the often disparate demands of convenience and conservation by grinding up kitchen scraps, especially non-compostable leftovers like meat and poultry or fat, and sending them down the drain to a sewage-treatment plant or septic system for handling, rather than to the landfill for slow decomposition. Our tests show that some disposers grind more quickly and finely, and are better at resisting jams.
FYI: I don't believe ISE is using the same quality metal causing these newer models to rust out quicker but, in my recent experience, I found that people who use their disposer properly will get at least 5 years service...that is acceptable for my purposes in the apartments. I did have 2 ISE disposers that only lasted about 2 years. One was from a tenant who almost never used it and allowed it to rust extensively and corrode from non-use. Using it helps keep it clean too. The second one, I determined was not being used properly, i.e., the tenant was not running water before turning on disposer causing food debris to accumulate in the small chamber below the blades/masticator.
Hang the disposal by aligning the three mounting tabs with the slide-up ramps on the mounting ring. Holding the disposal in place, turn the lower mounting ring until all three tabs are locked into the mounting assembly. The disposal will now hang by itself. Tighten the three mounting screws, ultimately tightening each screw a few turns at a time until the mounting assembly is evenly and tightly seated against the bottom of the sink.
Place a 1/2 inch rope of plumber's putty around the drain opening in the sink. Drop the new sink flange into the drain opening and press it into place. Placing a weight, such as a disposal, on top of the sink flange will help hold the sink flange in place while mounting the sink flange to the sink. To avoid scratching your sink or the flange, place a towel between the sink surface and the weight. (See Fig 4)
Next, you’ll connect the wires that you disconnected from the old disposer, to the new disposer. If this isn’t a replacement project, and you’re adding a new disposer where you didn’t have one before, you’ll first need to call an electrician to run the proper wires and a wall switch to the unit. For our project, the electrical wires and switch were already in place.
Rotate the disposer to align the disposer with the drain or the discharge tube, slide the flange over drain pipe or discharge tube and insert the gasket into the discharge outlet. Then screw in the bolts that secure the flange to the disposer. Reconnect all the plumbing connections as well as the dishwasher inlet hose. Then turn the power back on at the electrical supply panel and test the unit for leaks, making sure to run cold water while the unit is running.
If the garbage disposal won’t turn on, then it’s probably not getting power. First, make sure it’s plugged in. It’s easy to forget that disposals have wall outlets. It’s easy to knock a plug out of an outlet accidentally, especially in a dark place like under the sink. If the disposal is plugged in, check the reset button on the bottom of the disposal unit. If the disposal requires resetting, the button will be popped out. Simply press it and try the disposal again.
After all this, if your garbage disposal still refuses to turn on, it’s likely just broken. The motor could be burned out or there could be another related problem. If that’s the case, now is the time to get a new unit. Contact a plumber for garbage disposal replacement. If you live in the Pittsburgh area, contact Terry’s Plumbing. We’ll be happy to come out to your home, diagnose the problem with your garbage disposal, and replace the unit if necessary. To find out more, call us today at (412) 364-9114.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
Hot water, a good degreasing soap and a terrycloth rag. Try 409 degreaser and let it sit a few minutes, then run hot water on the cloth, add soap and rub the flange on top and underneath. There are commercial brushes available, but brushes don't always de-grease well. They are, however, very useful for cleaning crevices. Regular cleaning makes this job much easier.
Disposers fasten to the sink drain fittings in a number of ways--some use threaded plastic nuts, others large hose clamps--but the mounting-ring assembly shown here is the most common. To remove the disposer, support it from below and rotate the large, 3-tab mounting ring at the top counterclockwise until the unit falls away. Remove the remainder of the drain assembly by loosening the three bolts and prying off the retaining ring. Push the drain out through the sink hole and clear away any old caulk or putty.
Most people don’t think about the fact that garbage disposals are eco-friendly. By investing in a sink food disposer, you’ll be reducing the amount of trash that you leave on the curb for pickup. This means that less trash will be buried in your town’s local landfill. Conserving landfill space is a national concern, and it is one of multiple reasons why recycling is so important. Even though it might not seem like a lot to you, every conservation effort matters.
The Camorra was never a coherent whole nor a centralised organization. Instead, it has always been a loose confederation of different, independent groups or families. Each group was bound around kinship ties and controlled economic activities which took place in its particular territory. Each family clan took care of its own business, protected its territory, and sometimes tried to expand at another group’s expense. Although not centralized, there was some minimal coordination, to avoid mutual interference. The families competed to maintain a system of checks and balances between equal powers.