There are two main types of garbage disposers—continuous feed and batch feed. Continuous feed models are used by feeding in waste after being started and are more common. Batch feed units are used by placing waste inside the unit before being started. These types of units are started by placing a specially designed cover over the opening. Some covers manipulate a mechanical switch while others allow magnets in the cover to align with magnets in the unit. Small slits in the cover allow water to flow through. Batch feed models are considered safer, since the top of the disposal is covered during operation, preventing foreign objects from falling in.
First drop the garbage disposal down like in step 3. Loosen the 3 bolts that tighten the flange in place. Then locate the clip that holds the bottom flange in place. Use a flat screwdriver to pop the clip out of its groove. Then pull the top flange out from the top of the sink. Clean the area around the sink opening before reinstalling the flange making sure to remove any old putty.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below).
For over 75 years InSinkErator has been known for building the world's best food waste disposers. Badger, our standard disposer line, is basic, reliable, and functional. Available in various models and sizes for a range of applications, InSinkErator also manufactures a premier line of disposers, the Evolution Series. InSinkErator food waste disposers are the only disposers that are proudly made in the U.S.A. InSinkErator has grown into the largest food waste disposer manufacturer and best-selling garbage disposer brand in the world.
Roll out a generous amount of Plumber’s putty to a uniform width making a nice snake-like gasket out of putty. Wrap the putty onto the rim of the flange. Push the flange back into position and put the bottom flange on with the clip holding it into place. Tighten the three screws evenly until all three are tight. Scrape off any extra putty from the inside of the sink. Now you are ready to lock the garbage disposer back in place, reconnect the drains and test for leaks.
Leaks from the bottom of the garbage disposal (often from the reset button) commonly indicate that at least one seal on the interior shell of the unit that protects the motor has deteriorated, or that the shell itself has cracked. These vulnerabilities can cause water from the sink to seep into the shell of the disposal and leak out of the base of the unit. In an old garbage disposal, one compromised internal seal is often accompanied by others, so your best bet is to install a new one.
Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]

This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close


There are many potential causes for a leaky garbage disposal.  Luckily, identifying the cause of your garbage disposal’s leak is as simple as observing the source of the leak, and repairing the issue yourself is very doable.  Most often, if your garbage disposal is leaking, the cause can be identified and repaired yourself in short time, saving you the cost and hassle of replacing your entire disposal unit.
If your garbage disposal is making a clicking or rattling sound, there may be some food particles that will not grind up inside. Remove power from disposer, reach into the sink hole with a pair of tongs and remove anything that is still down in the disposer. Test your disposer to be sure the noise is gone. If not continue troubleshooting your disposer issue (see below). 

Garbage Disposal Replacement

×