The 2 800 RPM motor-powered dual stainless-steel swivel The 2 800 RPM motor-powered dual stainless-steel swivel impellers built into this GE 1/2 HP Continuous-Feed Garbage Disposal join forces with a 2-level pre-cutter to make it easy to grind undesirable waste into easily drainable particles. The disposer's large-capacity disposer chamber is comprised of a cold-rolled carbon steel armature shaft ...  More + Product Details Close
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright © 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
No need to worry if your garbage disposal is on the fritz—installing a new one is a straightforward project that you can do yourself in just a few minutes. Start by switching off the power to the disposal at your home’s breaker box to ensure that you can work safely. Next, remove the old unit by detaching it from the mounting ring directly beneath the sink drain. Finally, install any necessary new mounting hardware, fit the new disposal into place, and turn on the water to test for leaks before giving it a trial run.
For any major issues with the garbage disposal, you should leave the job to a professional plumber only. Reaching your hand into the drain is dangerous, even if you believe the power is shut off. A plumber can help you evaluate the state of your disposal, and decide whether or not you need a new unit. Upgrading to a faster disposal unit with a higher horsepower can help to protect your pipes and make cleaning up after meals even easier.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.

As a general rule of thumb, the heavier and bigger that a garbage disposal is, the more quietly it will operate – so long as it fits properly underneath your sink. Even though the sound dampening technology used in the design of garbage disposals has improved dramatically in the last 10 years, it is unrealistic to expect your garbage disposal to operate noise free. Under specific sinks, some disposals will be noisier than others due to the amount of vibration they produce. Ideally, you should look for a garbage disposal that features a nylon, insulated grinding chamber, like those produced by WasteKing.
The InSinkErator Badger 5 food waste disposal includes an exclusive, 'We Come to You' 2-Year In-Home Limited Warranty. This warranty includes free house calls (parts and labor) fulfilled through a network of 1500 professional service agents who are trained and certified to install, repair or replace InSinkErator disposers. Call our toll-free service line and we’ll provide you with the name and phone number of a factory authorized service agent nearest you.
Some folks knocked the instructions. Take heart. It appears that the Waste King guys have heard the criticisms from the negative reviewers. I am guessing that they have been re-written to better explain the installation because they are really easy to follow. My best advice is this: don't be afraid of a difficult or confounding set of installation instructions. It is really easy. Here's what you do. Go to youtube.com and search for a video on How To Remove Your Existing Garbage Disposal because this is the hardest part. You will find one that matches yours. Watch it. I started removing the Badger incorrectly, stopped, watched a video, and then it was a piece of cake. In my case, I shouldn't have removed the three long screws before removing the body of the old one. You do it after it is disconnected. READ the instruction manual carefully. Then go ahead and youtube the Waste King installation video. It is very easy once you see it done. No filing or grinding gaskets, and Good Lord, no car jacks under your sink please. If it is hard then you are doing something wrong. STOP!!! Review the procedure. Start again. The directions are actually very explicit. The parts are well labeled. The diagrams show you what to do. The videos show you what to do. If you prepare yourself (15 minutes of reading and watching videos, tops) you will fly though the installation and be a happy person.

Garbage Disposal Repair

×