Waste King L-8000: 1 horsepower garbage disposal with pre-installed power cord and sound insulation. Energy efficient permanent magnet motor and stainless steel swivel impellers reduce jamming. Fast and easy to install with a removable splashguard that is easy to clean and replace. Rust and corrosion-proof glass-filled nylon grind chamber and drain housing with stainless steel grinding components. Continuous feed technology. Front-mounted reset button for easy use. Safe to use with properly-sized septic tanks.
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Your garbage disposal gasket is the top rim where the rubber seal mounts to the flange.  If your disposer is leaking from this area, the cause could be a leaky gasket.  Gasket leaks can have several causes: ageing gaskets can develop leaks; long periods of disuse can dry the gasket and cause it to leak; if your garbage disposal was removed and then replaced, the gasket may have been improperly sealed; if the gasket is not locked evenly on all three sides, it will leak.

As one of the most important fixtures in your kitchen, your garbage disposal goes through extreme wear and tear on a day-to-day basis. To avoid accidental injury or further damage, don’t attempt to fix any unknown garbage disposal problems yourself. Instead, call the plumbers at Benjamin Franklin Plumbing to solve your problesm, whether you need  a repair, unclogging, or replacement.

Michele Zagaria, a senior member of the Casalesi clan, was arrested in 2011 after eluding police for 16 years. He was found in a secret bunker in the town Casapesenna, near Naples.[44] In 2014, clan boss Mario Riccio was arrested for drug trafficking in the Naples area. Around the same time 29 suspected Camorra members were also arrested in Rome.[45]

This Frigidaire 1/3 HP Garbage Disposal is designed This Frigidaire 1/3 HP Garbage Disposal is designed with features that deliver great performance. The High-Torque GrindPro Magnet Motor can grind through waste. Continuous-feed operation uses a wall switch to activate the stainless steel grinding system that is resistant to jamming and corrosion. Our sound guard design reduces noise level ...  More + Product Details Close
Quick Lock makes it fast & easy to switch out one InSinkErator garbage disposal for another. If you’re installing a disposal for the first time, all of the Quick Lock components you need come packed in the box. And then if it’s time to upgrade or replace your disposal, simply twist off the old one & twist on the new. The polished stainless steel InSinkErator sink flange will complement most stainless steel sinks and is compatible with most three-bolt mounting assemblies.
With the garbage disposal shopping, I quickly learned that the big brands are Waste King and Sinkerator and that those were the two best places to start. After going over several models and two trips to two separate best buys (who, by the way, really need to amp up their customer service model) I cheated and had my mom choose one for me. Sue me. So she chose this particular brand, and wow—it works really well, I can’t believe how easy it makes my life. I can put bones, and tough food products down the disposal, and it makes cooking really simple. Go figure.
In recent years, various Camorra clans have been forming alliances with Nigerian drug gangs and the Albanian mafia, even going so far as to intermarry.[citation needed] For instance, Augusto La Torre, the former La Torre clan boss who became a pentito, is married to an Albanian woman. It should also be noted that the first foreign pentito, a Tunisian, admitted to being involved with the feared Casalesi clan of Casal di Principe. The first town that the Camorra gave over to be completely governed by a foreign clan was Castel Volturno, which was given to the Rapaces, clans from Lagos and Benin City in Nigeria. This allowed them to traffic cocaine and women in sexual slavery before sending them across the whole of Europe.[33]
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
Most seals and pipes are located beneath your kitchen sink.  It is common for these pipes to be jarred when people are using that space.  If the pipes are struck hard enough, they can shift and sit improperly, causing retaining bolts to loosen and seals to be shifted into awkward positions.  If your leak is coming from this area, you will need to reattach and reseal these pipes.  Fixing this issue may require an experienced, licensed plumber.
3/4th Horsepower – This garbage disposal model is ideal for households of 4-5 people. It is the model that you will most commonly find in modern day homes. These models are often equipped with more sound dampening features, which reduce the level of noise the unit produces when compared to its lower end cousins. Again, it is recommended that you look for a model with stainless steel grinding components.
Another common cause for a leaking garbage disposal is the disposal flange. A leak at the very most upper area of the garbage disposal could be the garbage disposal flange which goes through the sink. A garbage disposal flange should be sealed with Plumber’s putty and then tightened from underneath the sink. If this is not tight enough or if it has managed to come loose (which can happen) then the garbage disposal will have to be taken down so the flange can be resealed and then the garbage disposal can be rehung.

Abt carries both types of garbage disposal systems, continuous and batch feed. Continuous feed disposers are turned on and off with a power switch. They usually have a shield surrounding the hole in the sink so things do not come back out while being ground for disposal. Some continuous feed disposals have a reverse setting to help reduce jamming. Batch feed disposals operate when a lid is engaged, making them safer. They are a good option for families with children because food is unable to fly out of the sink. Batch feed food waste disposals are usually more expensive than the continuous feed disposals.
Physically remove lodged objects. If a large object has become lodged in your garbage disposal, you will need to remove it before proceeding with the cleaning process. First, it is important that you turn off the fuse that supplies power to the disposal unit. This is to ensure that it does not turn on during cleaning. Alternatively, you may be able to unplug it from under the sink, depending on the design.
This is one of the biggest problems I’ve come across. When you start to notice a leak underneath your sink, it’s very easy to blame the quality of your garbage disposal. As you browse through the reviews on our website, you will probably notice I rarely mention a problem with leaking (if at all). This is because for the most part, the problem isn’t your unit but they way it has either been installed, or you could have a problem with the pipes it’s connected to.

If water is leaking from the disposal it more than likely needs a seal replaced but also could be a more serious problem. A leak can occur at the rings that are installed around the sink’s drain hole, called the sink flange. In that case, it can either be that the rings need to be tightened or that the plumber’s putty is faulty and needs to be reapplied correctly.


I think those are all the important items I wanted to share. The removal of the old one, cleaning the sink hole, and putting in the new box took about 35 minutes start to finish. I wasn't rushing but I was well prepared and had everything ready to go. Plumbers Putty was needed for install. Make sure you have that on hand. There was a thin rubber gasket that went under the flange (between the top flange and a stainless steel sink) that I didn't use because I didn't have a stainless steel sink. The one tricky thing I recall from the directions is that the same procedure is repeated twice in a couple of places - one for using the existing Badger mounting hardware and one for if you are using the EZ Mount system. If you are using the EZ Mount, make sure to SKIP the paragraph that is describing the work as it applies to the Badger mount. That's about it. I had to cut 3/4" off the black waste discharge pipe (90 degree elbow piece that screws into the new disposal) so that everything fit with my old plumbing. I loosened up all the slip joints on the old plumbing so I could wiggle things around as needed, aligned everything, and tightened the plumbing back up. New install was completed in well under 20 minutes after the removal and outlet installation.
Scotland has had its brush with the Camorra. Antonio La Torre of Aberdeen was the local "Don" of the Camorra. He is the brother of Camorra boss Augusto La Torre of the La Torre clan which had its base in Mondragone, Caserta. The La Torre Clan's empire was worth hundreds of millions of euros. Antonio had several legitimate businesses in Aberdeen, whereas his brother Augusto had several illegal businesses there. He was convicted in Scotland and is awaiting extradition to Italy. Augusto would eventually become a pentito in January 2003, confessing to over 40 murders and his example would be followed by many of his men.[54]
Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.

Remove all wet wipes, tissues, sanitary napkins, paper towels, and anything else in your bathroom that you wouldn't want someone to flush down the toilet. Despite the marketing claims that wet wipes are flushable, they are known for causing clogs and other plumbing problems. If someone needs these materials, they will ask, which will give you a great opportunity to explain what can and cannot be flushed down the toilet.
A 2-level pre-cutter joins forces with the 2 A 2-level pre-cutter joins forces with the 2 800 RPM motor-powered dual stainless-steel swivel impellers within this GE 1/2 HP Continuous-Feed Garbage Disposal to make the grinding and draining of undesirable food waste a snap. A manual reset overload protector helps safeguard the disposer from damage ensuring operational longevity. With ...  More + Product Details Close
Garbage disposals are considered nearly essential for modern kitchens. Installed underneath the sink, they grind up food into particles that will easily flush down a drain. A common problem with garbage disposals is that they will become jammed if too much food is pushed into them or a foreign object falls inside. When jammed, the circuit breaker may trip, cutting the power to the unit. When that happens, it will appear that the garbage disposal motor has burned out even though that may not be the case.

Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.

When rubber gaskets age, they can develop leaks. The gasket can dry up, crack, and leak when it is repeatedly exposed to long periods of disuse where no water is present in the drain pipe. Should an older garbage disposal be removed and then placed back, it will require a new rubber gasket to again achieve a watertight seal. Moreover, if a gasket is not evenly locked on all three sides, then it will develop a leak.
If the leak occurred under the sink and at the top of the disposal before you unplugged the sink drain, your leak is in the sink flange. This indicates that an improper seal exists between the unit and the sink, which can occur from corrosion or the disposal being bumped hard and out of place. This fix requires you to move the disposal altogether. Then apply a generous amount of plumber’s putty to the flange. Finally, replace the disposal and retighten the flange.
Garbage disposals are fairly straightforward machines. When something goes wrong with your garbage disposal, there are aren’t very many things you can do to troubleshoot your unit. This makes repairing your broken garbage disposal a relatively simple task. If your garbage disposal has broken, you can follow these tips to attempt to repair your unit.
Speaking of resetting your garbage disposal, sometimes that’s all you need to get the appliance up and running. However, if you constantly have to press the reset button for your garbage disposal to work, then there is an underlying problem. It may be insufficient wiring or regular wear and tear, but either way, it might be best to contact your local plumbing professional for help at this point.
In the United States, almost all garbage disposals on the market are manufactured by a handful of companies; although, many are branded under different names. For example, out of the top ten highest rated models on the market, InSinkErator makes eight of them. Whirlpool and WasteKing are the other two most well-known brands in the U.S. There are a wide range of models to choose from, ranging from basic $50.00 models to models equipped with all of the latest bells and whistles that can cost as much as $600.00. In most cases, you get what you pay for in terms of quality. Here is a brief overview of the top brands in the U.S.
However, whether the "high Camorra" was an integral part of the Camorra proper is disputed.[16] Although the inquiry did not prove specific collusion between the Camorra and politics, it brought to light the patronage mechanisms that fueled corruption in the municipality.[15] The society's influence was weakened which was exemplified by the defeat of all of their candidates in the 1901 Naples election. Many camorristi left for the United States in the early 20th century.[19]
To fix this problem, turn off the disposal, fill the sink halfway full with soapy water, and use a cup plunger to plunge the kitchen sink for 30 seconds to one minute. If you cleared the clog, the water in the sink should start draining at a normal pace again. If you’re still have issues, you might have to remove the P-trap under the sink to get at the clog with a snake.
We’re starting with clogs because they’re actually only *kind of* garbage disposal problems. Technically, garbage disposals can get jammed (see below!), but if water stands in your sink and takes forever to drain, it’s probably because the kitchen sink pipe has been clogged. Many different materials can cause clogs, from sediment, to scale, to grease, to food remains. Depending on the culprit, clogs may begin to smell. Ideally, your garbage disposal should have ground up debris enough that it wouldn’t clog anything up, but nobody’s perfect.

4. Is installing a garbage disposal worth the additional water expense? On average, a modern faucet runs 2.5 gallons of water per minute, or 900 gallons per year based upon the average annual household usage in the U.S. Depending on how often you use your disposerl, your home’s water usage, and water bill, will rise. This is one factor you’ll need to consider before deciding whether or not to buy a garbage disposal.
Your old discharge tube probably won’t be the right length for your new disposal. If it’s too long, simply connect it to the disposal, mark it and cut it with a hacksaw for your garbage disposal installation. (Loosen the other pipe connections, if necessary, to insert the tube back into the tee.) If the old discharge tube is too short, you may have to make a time-wasting trip to the store. To avoid this, make sure the new garbage disposal installation kit includes a tube, or buy one separately at the same time for about $3.
Flange: The flange is the uppermost portion of the garbage disposal, where the disposal and the sink drain meet. The flange can develop a leak for a variety of reasons. Check that all the mounting bolts, typically there are three, are tight enough. Snug the bolts up with a wrench if you see water dripping from any of the bolts, being careful not to overtighten the bolts.A second reason the flange may leak is if the seal, made of “plumber’s putty,” has failed. You will need to loosen the retaining bolts until you can see a gap around the flange. Force enough new putty in the gap, between the flange and the drain pipe, to fill in all the space. Tighten the retaining bolts.
If the water is leaking at the mounting assembly, make sure it is mounted as designed and not cocked. If the water is leaking at the dishwasher inlet, tighten the hose connector. If the water is leaking through the wall of the container body, your disposer probably need to be replaced. If the water is leaking from adjacent plumbing, tighten the connections as necessary.
Turn off the switch, unplug it, clear any debris inside the disposal, and rinse with warm water. Many times there is something stuck in the blades that they can't handle (citrus peels, meats, stringy vegetables, etc.). You may need to turn the blades manually to find a lodged object, and it may even be under the blade. Find the reset button (usually red) and hold it for 1 minute. Plug it in, try again. Some newer models do not have the reset button, there is an opening on the bottom of the disposal to insert an allen wrench. If not, look up your model by manufacturer or Google for further instructions.
What's up with that scary loud noise when you turn it on? There are some reviews that make this sound like it is eating a spoon (a LOUD, disturbing, and/or startling snap or click noise, etc.). I have to say that was one of my biggest reservations when I ordered this thing, having read the reviews. A fairly large slice of reviewers commented negatively on it. Here's my take... The motor is 3/4 HP compared to my little dinky 1/3 HP motor on my old one. That is a lot more horsepower and, consequently, a lot more torque. The little "teeth" that do the waste grinding that sit in the base of the chamber spin freely. When you turn it on, the little grinders snap into place like how your head gets whipped back on one of those crazy spinning carnival rides. It's just from centrifugal force setting the blades into place. The fine print in the directions tell you that it is part of the anti-jam mechanism. It's not startling or even disconcerting to me or my wife. We didn't blink an eye. I couldn't scare my children by turning it on. It just makes a bit of a click when you turn it on. No biggie. Full disclosure here - ours is mounted to the bottom of a heavy, porcelain coated cast iron sink. Our sink may be better at handling the torque and may dampen the sound and vibration more than a thin stainless steel sink. Our sink weighs probably 75 pounds. A stainless steel sink weighs 7 pounds. A heavier sink can probably handle a garbage disposal operating under full load better than a flexible, lightweight sink. That's not why we got the sink but I think it's probably a benefit to damping sounds and vibrations.
The good news is that a leaking gasket can be easily replaced. Most home improvement or local hardware stores will carry them, and they are usually inexpensive. However, depending on the particular model of your garbage disposal, it may require a specially fitted rubber gasket. To ensure that you get the right gasket the first time, write down your garbage disposal’s model number, take it to the store, and ask an employee to match it up for you.
In 2004 and 2005 the Di Lauro clan and the so-called Scissionisti di Secondigliano fought a bloody feud which came to be known in the Italian press as the Scampia feud. The result was over 100 street killings. At the end of October 2006 a new series of murders took place in Naples between 20 competing clans, that cost 12 lives in 10 days. The Interior Minister Giuliano Amato decided to send more than 1,000 extra police and carabinieri to Naples to fight crime and protect tourists.[31] Despite this, in the following year there were over 120 murders.[citation needed]
Make sure the reset button on the bottom is not popped out. If your disposal has a cord, make sure it is plugged in and there is power to the disposal. If your disposal has a cord, and there is no power to the disposal, check the breaker or GFI on the wall. If your disposer is hard wired into the wall, check the circuit breaker behind the electrical panel. If humming it is probably jammed. Use the small wrench that can with your disposal to unjam it and stop it from humming.
Connect the new mounting assembly. Working in reverse order now, slide a rubber gasket over the bottom of the new sink flange, followed by a second metal flange. Position the new mounting ring last and insert screws into each of the open screw holes. Hold the assembly in place with one hand while you tighten the screws up against the lower flange with the other.[14]
There is a contradiction among some of the brands. InSinkErator’s disposal instruction manual states, “Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc, to avoid possible drain blockage.” Whirlpool’s disposal instruction manual states, “designed to dispose of food wastes including bones, fruit and vegetable wastes, pits, egg shells and coffee grounds.”

Garbage disposal units have standard hook-ups that are present on all models from every manufacturer. They all have an inlet and an outlet and a dishwasher inlet on the side, and a disposal unit can leak in those areas. If the body of the unit is leaking, the unit must be replaced, but other leaks in a disposal unit can be repaired by a do-it-yourselfer who has basic skills.
The size of the motor in the garbage disposal directly correlates to the units grinding ability. Garbage disposals typically have between 1/3-1 horsepower motors. Choose the correct horsepower based on the waste that you need to remove. 1/3 horsepower units will help tackle tasks like grinding vegetables easily, but more power is recommended if disposing a large quantity of food waste such as, vegetables and harder to grind meats.
While it certainly isn’t always necessary to replace your disposal just because you’re getting a new sink or updating your kitchen appliances, it may be a good time to do so, especially if your unit is over ten years old. Since you already have professionals on the site, it may be more cost efficient and convenient to go ahead and replace an older unit instead of waiting for it to fail at a future date.

A. First, troubleshoot a bit. You can stick something down the drain (not your fingers) to try and dislodge whatever may be causing the blockage. You can also try using a shop vac to unblock the drain. If these options don’t work, cut the electricity connection to your device before you go inside to try and remove anything that’s stuck. If you still can’t find the culprit, call a professional. Your unit may be damaged.
A sink flange is the uppermost portion of a garbage disposal.  It is the point where the sink, drain, and garbage disposal meet, and it keeps debris from clogging your drain.  If you have a leak at the uppermost area of your garbage disposal, the source is likely your garbage disposal flange.  The two most likely reasons for a flange leak are that the mounting bolts have loosened and that the plumber’s putty has failed.
Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
×